Asus TUF GAMING B760M-PLUS WIFI Users Manual English - Page 16

Reset button header RESET, Chassis intrusion header CHASSIS, Thunderbolt™ USB4, header, Q-LEDs

Get Asus TUF GAMING B760M-PLUS WIFI PDF manuals and user guides View all Asus TUF GAMING B760M-PLUS WIFI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

• Reset button header (RESET) The 2-pin header allows you to connect the chassis-mounted reset button. Press the reset button to reboot the system. • Chassis intrusion header (CHASSIS) The 2-pin header allows you to connect the chassis-mounted intrusion detection sensor or switch. The chassis intrusion sensor or switch sends a high-level signal to the header when a chassis component is removed or replaced, the signal is then generated as a chassis intrusion event. 16. Thunderbolt™ (USB4®) header The Thunderbolt™ (USB4®) header allows you to connect an addon card that supports Intel®'s Thunderbolt™ Technology or USB4® function. • The add-on card is purchased separately. • Please visit the official website of your purchased add-on card for more details on compatibility. I2C_SCL I2C_SDA I2C_IRQ# RTD3_POWER_EN NC PERST_N WAKE# TB(USB4)_HEADER PIN 1 The add-on card can only be used when installed to the PCIEX16(G4) slot. Ensure to install your add-on card to the PCIEX16(G4) slot. FORCE_PWR CIO_PLUG_EVENT SLP_S3# SLP_S5# GND RTD3_SW 17. Q-LEDs The Q-LEDs check key components (CPU, DRAM, VGA, and booting devices) during the motherboard booting process. If an error is found, the critical component's LED stays lit up until the problem is solved. The Q-LEDs provide the most probable cause of an error code as a starting point for troubleshooting. The actual cause may vary from case to case. 1-6 Chapter 1: Product Introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
1-6
•
Reset button header (RESET)
The 2-pin header allows you to connect the chassis-mounted reset button. Press the
reset button to reboot the system.
•
Chassis intrusion header (CHASSIS)
The 2-pin header allows you to connect the chassis-mounted intrusion detection
sensor or switch. The chassis intrusion sensor or switch sends a high-level signal
to the header when a chassis component is removed or replaced, the signal is then
generated as a chassis intrusion event.
16. Thunderbolt™ (USB4
®
) header
The Thunderbolt™ (USB4
®
) header allows you to connect an add-
on card that supports Intel
®
’s Thunderbolt™ Technology or USB4
®
function.
•
The add-on card is purchased separately.
•
Please visit the official website of your purchased add-on
card for more details on compatibility.
The add-on card can only be used when installed to the
PCIEX16(G4) slot. Ensure to install your add-on card to the
PCIEX16(G4) slot.
17. Q-LEDs
The Q-LEDs check key components (CPU, DRAM, VGA, and booting devices) during the
motherboard booting process. If an error is found, the critical component’s LED stays lit up
until the problem is solved.
The Q-LEDs provide the most probable cause of an error code as a starting point for
troubleshooting. The actual cause may vary from case to case.
PIN 1
FORCE_PWR
CIO_PLUG_EVENT
SLP_S3#
SLP_S5#
GND
RTD3_SW
I2C_SCL
I2C_SDA
I2C_IRQ#
RTD3_POWER_EN
NC
PERST_N
WAKE#
TB(USB4)_HEADER
Chapter 1: Product Introduction