Asus V2-AH2 Quick Installation Guide - Page 8

Removing the bay covers and reinstalling the, front panel assembly and side cover

Get Asus V2-AH2 PDF manuals and user guides View all Asus V2-AH2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

English 4. For SATA HDD: Connect the SATA signal and power plugs to SATA IDE the connectors at the back of the drive. For IDE HDD: Connect the IDE signal and power plugs to the connectors at the back of the drive. Removing the bay covers and reinstalling the front panel assembly and side cover If you installed an optical and/or floppy disk drive, remove the bay cover(s) on the front panel assembly before reinstalling it to the chassis. To do this: 1. Locate the bay cover locks. 2. Press the locks outward to release the bay cover. 3. Push the bay cover inward, then set it aside. 4. Follow the same instructions to remove the 3.5" drive bay cover. To reinstall the front panel assembly and side cover: 1. Insert the front panel assembly hinge-like tabs to the holes on the right side of the chassis. 2. Swing the front panel assembly to the left, then insert the hooks to the chassis until the front panel assembly fits in place. 3. Insert the side cover hooks to the chassis top and bottom holes. 4. Push the side cover to the direction of the front panel until it fits in place. 5. Secure the cover with two screws you removed earlier. 2 1 5 Air duct 4 2 1 5 3 Chassis tab holes 1 2 2  Quick installation guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
8
Quick installation guide
English
4.
For SATA HDD: Connect the
SATA signal and power plugs to
the connectors at the back of
the drive.
For IDE HDD: Connect the IDE
signal and power plugs to the
connectors at the back of the drive.
SATA
IDE
Removing the bay covers and reinstalling the
front panel assembly and side cover
If you installed an optical and/or floppy disk drive, remove the bay cover(s)
on the front panel assembly before reinstalling it to the chassis. To do this:
1.
Locate the bay cover locks.
±.
Press the locks outward to
release the bay cover.
3.
Push the bay cover inward, then
set it aside.
4.
Follow the same instructions to
remove the 3.5” drive bay cover.
To reinstall the front panel assembly and side cover:
1.
Insert the front panel assembly hinge-like tabs to the holes on the
right side of the chassis.
±.
Swing the front panel assembly to the left, then insert the hooks to
the chassis until the front panel assembly fits in place.
3.
Insert the side cover hooks to the chassis top and bottom holes.
4.
Push the side cover to the direction of the front panel until it fits in place.
5.
Secure the cover with two screws you removed earlier.
5
Air duct
5
4
3
±
1
±
±
±
1
1
Chassis tab holes