Asus V3-P5P43 Installation Manual - Page 4

Selecting the voltage, Removing the side cover andfront panel assembly

Get Asus V3-P5P43 PDF manuals and user guides View all Asus V3-P5P43 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

English Selecting the voltage The system's power supply unit has a 115 V/230 V voltage selector switch located beside the power connector. Use this switch to select the appropriate system input voltage according to the voltage supply in your area. If the voltage supply in your area is 100‑127 V, set the switch to 115 V. If the voltage supply in your area is 200‑240 V, set the switch to 230 V. NOTE: Refer to the system User Guide for the exact location of the voltage selector. Removing the side cover and front panel assembly 1. Remove the cover screws on the rear panel. 2. Pull the side cover toward the rear panel until its hooks disengage from the chassis tab holes. Set the side cover aside. 3. Locate the front panel assembly hooks, then lift them until they disengage from the chassis. 4. Swing the front panel assembly to the right, until the hinge-like tabs on the right side of the assembly are exposed. 5. Remove the front panel assembly, then set aside. 3 4 Air duct 1 23 4 1 4 3 2 Chassis tab holes 3  Installation manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
³
Installation manual
English
Selecting the voltage
The system’s power supply unit has a 115
V/230 V voltage selector switch located
beside the power connector. Use this
switch to select the appropriate system
input voltage according to the voltage
supply in your area.
If the voltage supply in your area is
100-127 V, set the switch to 115 V.
If the voltage supply in your area is
200-240 V, set the switch to 230 V.
Removing the side cover and
front panel assembly
1.
Remove the cover screws on the rear panel.
2.
Pull the side cover toward the rear panel until its hooks disengage from the
chassis tab holes. Set the side cover aside.
3.
Locate the front panel assembly hooks, then lift them until they disengage
from the chassis.
4.
Swing the front panel assembly to the right, until the hinge-like tabs on the
right side of the assembly are exposed.
5.
Remove the front panel assembly, then set aside.
Air duct
1
1
2
2
4
3
4
4
3
3
3
Chassis tab holes
NOTE:
Refer to the system User Guide for the exact location of the voltage selector.