Asus VivoStick PC TS10 VivoStick TS10 Users manual English/Traditional Chinese - Page 2

ASUS Contact Information - singapore

Page 2 highlights

Safety information Your VivoStick is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions. Setting up your system • Read and follow all instructions in the documentation before you operate your system. • Do not use this product near water or a heated source. • Make sure you leave plenty of space around the system for ventilation. • Use this product in environments with ambient temperatures between 1˚C (33.8˚F) and 35˚C (95˚F). • If you use an extension cord, make sure that the total ampere rating of the devices plugged into the extension cord does not exceed its ampere rating. • If you notice any of the following conditions (or if you have other safety concerns), do not use your device: crackling, hissing, popping sound, or a strong odor or smoke coming from your device. It is normal for these conditions to appear when an internal electronic component fails in a safe and controlled manner. However, these conditions may also indicate a potential safety issue. Do not assume that it is a safe failure. Turn off your device. If your device is plugged in, disconnect it from its power source, and contact technical support for assistance. • Magnet: Avoid placing any media that contains magnets or is sensitive to magnetism, such as credit cards, bank cards, audio/video, tapes, or magnetic memory devices, near your device as you may lose information stored on that media and devices may be severely damaged. Media containing information sensitive to magnets should be kept at least 5 cm away from your device. • Pacemakers and other implanted medical devices: VivoStick receives and transmits using Wi-Fi and Bluetooth technology, which can interfere with pacemakers and other implanted medical devices. If you have a pacemaker or other implanted medical device, contact your physician or medical device manufacturer to make sure it's okay to use your VivoStick. Care during use • Do not walk on the power cord or allow anything to rest on it. • Do not spill water or any other liquids on your system. • When the system is turned off, a small amount of electrical current still flows. Always unplug the power cord from the power outlets before cleaning the system. • If you encounter the following technical problems with the product, unplug the power cord and contact a qualified service technician or your retailer. -The power cord or plug is damaged. -Liquid has been spilled into the system. -The system does not function properly even if you follow the operating instructions. -The system was dropped or the casing is damaged. -The system performance changes. Lithium-Metal Battery Warning CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. NO DISASSEMBLY The warranty does not apply to the products that have been disassembled by users. DO NOT throw the VivoStick in municipal waste. This product has been designed to enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin indicates that the product (electrical, electronic equipment, and mercury-containing button cell battery) should not be placed in municipal waste. Check local technical support services for product recycling. Regulatory notices REACH Complying with the REACH (Registration, Evaluation, Authorization, and Restriction of Chemicals) regulatory framework, we publish the chemical substances in our products at ASUS REACH website at http://csr.asus.com/ english/REACH.htm ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components, as well as the packaging materials. Please go to http:// csr.asus.com/english/Takeback.htm for the detailed recycling information in different regions. Regional notice for California WARNING! This product may contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Wash hands after handling. Coating Notice IMPORTANT! To provide electrical insulation and maintain electrical safety, a coating is applied to insulate the device except on the areas where the I/O ports are located. 「PC PC PC PC PC ご注意: PC ・ 「PC PC JIS C 0950: 2008 (J-Moss J-Moss JIS The marking when content other than exemption does not exceed reference value of percentage content 2008年8月1 ASUS http://csr.asus.com The marking when content other than exemption does not exceed reference value of percentage content Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer's instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Declaration of Conformity (R&TTE directive 1999/5/EC)* * Replaced in 2017 by RED 2014/53/EU The following items were completed and are considered relevant and sufficient: • Essential requirements as in [Article 3] • Protection requirements for health and safety as in [Article 3.1a] • Testing for electric safety according to [EN 60065] • Protection requirements for electromagnetic compatibility in [Article 3.1b] • Testing for electromagnetic compatibility according to [EN 301 489-1] & [EN 301 489-17] • Effective use of the radio spectrum as in [Article 3.2] • Radio test suites according to [EN 300 328-2] France Restricted Wireless Frequency Bands Some areas of France have a restricted frequency band. The worst case maximum authorized power indoors are: • 10mW for the entire 2.4 GHz band (2400 MHz-2483.5 MHz) • 100mW for frequencies between 2446.5 MHz and 2483.5 MHz NOTE: Channels 10 through 13 inclusive operate in the band 2446.6 MHz to 2483.5 MHz. There are few possibilities for outdoor use: On private property or on the private property of public persons, use is subject to a preliminary authorization procedure by the Ministry of Defense, with maximum authorized power of 100mW in the 2446.5-2483.5 MHz band. Use outdoors on public property is not permitted. In the departments listed below, for the entire 2.4 GHz band: • Maximum authorized power indoors is 100mW • Maximum authorized power outdoors is 10mW Departments in which the use of the 2400-2483.5 MHz band is permitted with an EIRP of less than 100mW indoors and less than 10mW outdoors: 01 Ain 02 Aisne 03 Allier 05 Hautes Alpes 08 Ardennes 09 Ariège 11 Aude 12 Aveyron 16 Charente 24 Dordogne 25 Doubs 26 Drôme 32 Gers 36 Indre 37 Indre et Loire 41 Loir et Cher 45 Loiret 50 Manche 55 Meuse 58 Nièvre 59 Nord 60 Oise 61 Orne 63 Puy du Dôme 64 Pyrénées Atlantique 66 Pyrénées Orientales 67 Bas Rhin 70 Haute Saône 71 Saône et Loire 75 Paris 82 Tarn et Garonne 84 Vaucluse 88 Vosges 89 Yonne 90 Territoire de 94 Val de Marne Belfort This requirement is likely to change over time, allowing you to use your wireless LAN card in more areas within France. Please check with ART for the latest information (www.art-telecom.fr) NOTE: Your WLAN Card transmits less than 100mW, but more than 10mW. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003. IC Radiation Exposure Statement for Canada This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with IC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting. End users must follow the specific operating instructions for satisfying RF exposure compliance. Operation is subject to the following two conditions: • This device may not cause interference and • This device must accept any interference, including interference that may cause undesired operation of the device. ICES-3(B)-NMB(3)(B) User should also be advised that: (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and (iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LELAN devices. CE Mark Warning CE marking for devices without wireless LAN/Bluetooth The shipped version of this device complies with the requirements of the EMC directives 2004/108/EC (replaced in April 2016 by 2014/30/EU) "Electromagnetic compatibility" and 2006/95/EC (replaced in April 2016 by 2014/35/EU) "Low voltage directive". CE marking for devices with wireless LAN/ Bluetooth This equipment complies with the requirements of Directive 1999/5/EC (replaced in 2017 by RED 2014/53/EU) of the European Parliament and Commission from 9 March, 1999 governing Radio and Telecommunications Equipment and mutual recognition of conformity. Wireless Operation Channel for Different Domains N. America 2.412-2.462 GHz Ch01 through CH11 Japan 2.412-2.484 GHz Ch01 through Ch14 Europe ETSI 2.412-2.472 GHz Ch01 through Ch13 Regional notice for Singapore Complies with IDA Standards DB103778 This ASUS product complies with IDA Standards. ASUS Contact Information ASUSTeK COMPUTER INC. Address Telephone Fax Website 4F, No. 150 Li-Te Road, Peitou, Taipei 112, Taiwan +886-2-2894-3447 +886-2-2890-7798 http://www.asus.com Technical Support Telephone +86-21-38429911 Fax +86-21-58668722, ext. 9101# Online support http://qr.asus.com/techserv ASUS COMPUTER INTERNATIONAL (America) Address Telephone Fax Website 800 Corporate Way, Fremont, CA 94539, USA +1-510-739-3777 +1-510-608-4555 http://usa.asus.com Technical Support Support fax +1-812-284-0883 General support +1-812-282-4555 Online support http://qr.asus.com/techserv ASUS COMPUTER GmbH (Germany and Austria) Address Fax Website Harkort Str. 21-23, D-40880 Ratingen, Germany +49-2102-959931 http://www.asus.com/de Technical Support Telephone +49-2102-5789555 Support Fax +49-2102-959911 Online support http://qr.asus.com/techserv DECLARATION OF CONFORMITY Per FCC Part 2 Section 2. 1077(a) Responsible Party Name: Asus Computer International Address: 800 Corporate Way, Fremont, CA 94539. Phone/Fax No: (510)739-3777/(510)608-4555 hereby declares that the product Product Name : VivoStick Model Number : TS10 Conforms to the following specifications: FCC Part 15, Subpart B, Unintentional Radiators Supplementary Information: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Representative Person's Name : Steve Chang / President Signature : Date : Feb. 22, 2016 Ver. 140331

  • 1
  • 2

Regulatory notices
REACH
Complying with the REACH (Registration, Evaluation, Authorization, and
Restriction of Chemicals) regulatory framework, we publish the chemical
substances in our products at ASUS REACH website at
english/REACH.htm
RF exposure warning
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed
to provide a separation distance of at least 20 cm from all persons and
must not be co-located or operating in conjunction with any other antenna
or transmitter. End-users and installers must be provide with antenna
installation instructions and transmitter operating conditions for satisfying
RF exposure compliance.
France Restricted Wireless Frequency Bands
Some areas of France have a restricted frequency band. The worst case
maximum authorized power indoors are:
10mW for the entire 2.4 GHz band (2400 MHz–2483.5 MHz)
100mW for frequencies between 2446.5 MHz and 2483.5 MHz
NOTE:
Channels 10 through 13 inclusive operate in the band 2446.6 MHz
to 2483.5 MHz.
There are few possibilities for outdoor use: On private property or on
the private property of public persons, use is subject to a preliminary
authorization procedure by the Ministry of Defense, with maximum
authorized power of 100mW in the 2446.5–2483.5 MHz band. Use outdoors
on public property is not permitted.
In the departments listed below, for the entire 2.4 GHz band:
Maximum authorized power indoors is 100mW
Maximum authorized power outdoors is 10mW
Departments in which the use of the 2400–2483.5 MHz band is permitted
with an EIRP of less than 100mW indoors and less than 10mW outdoors:
01
Ain
02
Aisne
03
Allier
05
Hautes Alpes
08
Ardennes
09
Ariège
11
Aude
12
Aveyron
16
Charente
24
Dordogne
25
Doubs
26
Drôme
32
Gers
36
Indre
37
Indre et Loire
41
Loir et Cher
45
Loiret
50
Manche
55
Meuse
58
Nièvre
59
Nord
60
Oise
61
Orne
63
Puy du Dôme
64
Pyrénées
Atlantique
66
Pyrénées
Orientales
67
Bas Rhin
70
Haute Saône
71
Saône et Loire
75
Paris
82
Tarn et
Garonne
84
Vaucluse
88
Vosges
89
Yonne
90
Territoire de
Belfort
94
Val de Marne
This requirement is likely to change over time, allowing you to use your
wireless LAN card in more areas within France. Please check with ART for the
latest information (www.art-telecom.fr)
NOTE:
Your WLAN Card transmits less than 100mW, but more than
10mW.
CE Mark Warning
CE marking for devices without wireless LAN/Bluetooth
The shipped version of this device complies with the requirements of
the EMC directives 2004/108/EC (replaced in April 2016 by 2014/30/EU)
“Electromagnetic compatibility” and 2006/95/EC (replaced in April 2016 by
2014/35/EU)“Low voltage directive”.
CE marking for devices with wireless LAN/ Bluetooth
This equipment complies with the requirements of Directive 1999/5/EC
(replaced in 2017 by RED 2014/53/EU) of the European Parliament and
Commission from 9 March, 1999 governing Radio and Telecommunications
Equipment and mutual recognition of conformity.
Regional notice for Singapore
This ASUS product complies with IDA Standards.
Complies with
IDA Standards
DB103778
Wireless Operation Channel for Different
Domains
N. America
2.412-2.462 GHz
Ch01 through CH11
Japan
2.412-2.484 GHz
Ch01 through Ch14
Europe ETSI
2.412-2.472 GHz
Ch01 through Ch13
ASUS Contact Information
ASUSTeK COMPUTER INC.
Address
4F, No. 150 Li-Te Road, Peitou, Taipei 112, Taiwan
Telephone
+886-2-2894-3447
Fax
+886-2-2890-7798
Website
Technical Support
Telephone
+86-21-38429911
Fax
+86-21-58668722, ext. 9101#
Online support
ASUS COMPUTER INTERNATIONAL (America)
Address
800 Corporate Way, Fremont, CA 94539, USA
Telephone
+1-510-739-3777
Fax
+1-510-608-4555
Website
Technical Support
Support fax
+1-812-284-0883
General support
+1-812-282-4555
Online support
ASUS COMPUTER GmbH (Germany and Austria)
Address
Harkort Str. 21-23, D-40880 Ratingen, Germany
Fax
+49-2102-959931
Website
Technical Support
Telephone
+49-2102-5789555
Support Fax
+49-2102-959911
Online support
Safety information
Your VivoStick is designed and tested to meet the latest standards of safety
for information technology equipment. However, to ensure your safety, it is
important that you read the following safety instructions.
Setting up your system
Read and follow all instructions in the documentation before you
operate your system.
Do not use this product near water or a heated source.
Make sure you leave plenty of space around the system for ventilation.
Use this product in environments with ambient temperatures between
1˚C (33.8˚F) and 35˚C (95˚F).
If you use an extension cord, make sure that the total ampere rating
of the devices plugged into the extension cord does not exceed its
ampere rating.
If you notice any of the following conditions (or if you have other
safety concerns), do not use your device: crackling, hissing, popping
sound, or a strong odor or smoke coming from your device. It is normal
for these conditions to appear when an internal electronic component
fails in a safe and controlled manner. However, these conditions may
also indicate a potential safety issue. Do not assume that it is a safe
failure. Turn off your device. If your device is plugged in, disconnect it
from its power source, and contact technical support for assistance.
Magnet
: Avoid placing any media that contains magnets or is
sensitive to magnetism, such as credit cards, bank cards, audio/video,
tapes, or magnetic memory devices, near your device as you may
lose information stored on that media and devices may be severely
damaged. Media containing information sensitive to magnets should
be kept at least 5 cm away from your device.
Pacemakers and other implanted medical devices
: VivoStick
receives and transmits using Wi-Fi and Bluetooth technology, which
can interfere with pacemakers and other implanted medical devices. If
you have a pacemaker or other implanted medical device, contact your
physician or medical device manufacturer to make sure it’s okay to use
your VivoStick.
DO NOT
throw the VivoStick in municipal waste. This product has
been designed to enable proper reuse of parts and recycling. This
symbol of the crossed out wheeled bin indicates that the product
(electrical, electronic equipment, and mercury-containing button
cell battery) should not be placed in municipal waste. Check local
technical support services for product recycling.
NO DISASSEMBLY
The warranty does not apply to the products that have been
disassembled by users.
Lithium-Metal Battery Warning
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended
by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
Federal Communications Commission
Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter. Any changes or
modifications not expressly approved by the grantee of this device could
void the user’s authority to operate the equipment.
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the
highest standards for protecting our environment. We believe in providing
solutions for you to be able to responsibly recycle our products, batteries,
other components, as well as the packaging materials. Please go to
http://
csr.asus.com/english/Takeback.htm
for the detailed recycling information
in different regions.
Coating Notice
IMPORTANT!
To provide electrical insulation and maintain electrical
safety, a coating is applied to insulate the device except on the areas
where the I/O ports are located.
Declaration of Conformity (R&TTE directive
1999/5/EC)*
* Replaced in 2017 by RED 2014/53/EU
The following items were completed and are considered relevant and
sufficient:
Essential requirements as in [Article 3]
Protection requirements for health and safety as in [Article 3.1a]
Testing for electric safety according to [EN 60065]
Protection requirements for electromagnetic compatibility in [Article 3.1b]
Testing for electromagnetic compatibility according to [EN 301 489-1]
& [EN 301 489-17]
Effective use of the radio spectrum as in [Article 3.2]
Radio test suites according to [EN 300 328-2]
Care during use
Do not walk on the power cord or allow anything to rest on it.
Do not spill water or any other liquids on your system.
When the system is turned off, a small amount of electrical current still
flows. Always unplug the power cord from the power outlets before
cleaning the system.
If you encounter the following technical problems with the product,
unplug the power cord and contact a qualified service technician or
your retailer.
–The power cord or plug is damaged.
–Liquid has been spilled into the system.
–The system does not function properly even if you follow the
operating instructions.
–The system was dropped or the casing is damaged.
–The system performance changes.
回収とリサイクルについて
使用済みのコンピューター、ノートパソコン等の電子機器には、環境
に悪影響を与える有害物質が含まれており、通常のゴミとして廃棄す
ることはできません。リサイクルによって、使用済みの製品に使用さ
れている金属部品、プラスチック部品、各コンポーネントは粉砕さ
れ新しい製品に再使用されます。また、その他のコンポーネントや部
品、物質も正しく処分・処理されることで、有害物質の拡散の防止と
なり、環境を保護することに繋がります。
筐体のコーティングについて
重要:
感電などを防ぐため、本機は絶縁性のあるコーティング材を
使用しています(出入力ポート搭載部分を除く)。
「PCリサイクルマーク」の取り扱
いに付いて
この製品には「PCリサイクルマーク」シールが同梱されています。製
品の使用停止後、弊社にPCリサイクルをご依頼いただく際に必要とな
りますので「PCリサイクルマーク」シールをPCの本体に貼り付けてく
ださい。
ご注意:
同梱された「PCリサイクルマーク」シールは本
製品以外には貼り付けないでください。
「PCリサイクルマーク」シールは通風孔を塞が
ない場所を選んで貼り付けてください。
同梱された「PCリサイクルマーク」シールを紛
失された場合、再発行は出来ません。
電気・電子機器に含有される化学物
質の表示について
資源有効利用促進法では、
JIS C 0950: 2008 (J-Moss) の定める規格
により、製造元に対し特定の電気・電子機器に含まれる化学物質の
情報提供を義務付けています。
J-Moss とは、電気・電子機器に含有
される化学物質の表示に関するJIS規格の略称で、正式名称は「The
marking when content other than exemption does not exceed
reference value of percentage content (電気・電子機器の特定の
化学物質の含有表示方法) 」です。なお、この規格は2008年8月1日よ
り適用されています。
この規格に関する詳細情報はASUSのサイト (http://csr.asus.com)
に記載の「The marking when content other than exemption
does not exceed reference value of percentage content (電気・電
子機器の特定の化学物質の含有表示方法) 」をご参照ください。
Regional notice for California
WARNING!
This product may contain chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm. Wash
hands after handling.
DECLARATION OF CONFORMITY
Per FCC Part 2 Section 2. 1077(a)
Responsible Party Name:
Asus Computer International
Address:
800 Corporate Way, Fremont
, CA 94539.
Phone/Fax No:
(510)739-3777/(510)608-4555
hereby declares that the product
Product Name : VivoStick
Model Number : TS10
Conforms to the following specifications:
FCC Part 15, Subpart B, Unintentional Radiators
Supplementary Information:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Representative Person’s Name
:
Steve Chang / President
Signature :
Date :
Feb. 22, 2016
Ver. 140331
Canadian Department of Communications
Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
IC Radiation Exposure Statement for
Canada
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. To maintain compliance with IC RF exposure
compliance requirements, please avoid direct contact to the transmitting
antenna during transmitting. End users must follow the specific operating
instructions for satisfying RF exposure compliance.
Operation is subject to the following two conditions:
This device may not cause interference and
This device must accept any interference, including interference that
may cause undesired operation of the device.
ICES-3(B)-NMB(3)(B)
User should also be advised that:
(i) the device for operation in the band 5150-5250 MHz is only for indoor
use to reduce the potential for harmful interference to co-channel mobile
satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350
MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and
(iii) the maximum antenna gain permitted for devices in the band 5725-5825
MHz shall comply with the e.i.r.p. limits specified for point-to-point and non
point-to-point operation as appropriate. High-power radars are allocated as
primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850
MHz and that these radars could cause interference and/or damage to LE-
LAN devices.