Audiovox EZCRG Owners Manual - Page 4

Contents in Kit, E. Tools Required not supplied, F. Installation Guide

Get Audiovox EZCRG - Mini EZ Fit Console PDF manuals and user guides View all Audiovox EZCRG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

NOTE: Whenever unit loading exceeds 3 Amperes, the unit power supply will overload and automatically disconnect the power supply from +12V DC vehicle power at the cigarette lighter jack. D. Contents in Kit TV and VCP Floor Console Owner's Manual Remote Control 12V Cigarette Lighter Cord and Plug (for powering this unit) Cardboard Mounting Template (for positioning the mounting holes on the floor) Hardware Package for Securing Console to Vehicle Contains the following: 6 Floor Bolts 6 Sealing Washers 6 Fender Washers 6 Floor Nuts 2 Console Bolts 2 Spring Washers 1 Mounting Plate E. Tools Required (not supplied) Electric Drill 1/8" Steel Drill Bit 1/4" Steel Drill Bit Socket Wrench Set with Deep-Wall, 7/16" Socket Box Wrench, Size 7/16" Standard Utility Knife (or Equivalent) NOTE: Two people are required for installation. F. Installation Guide (Refer to Figure 2) 1. Temporarily place the cardboard mounting template on an appropriate mounting location on the floor between driver/passenger seats, with the rounded end of the template facing the front of your vehicle. Make sure that you have checked both underneath the vehicle and within the vehicle (under the carpet) for obstructions. 2. Drill 6 small 1/8" pilot holes though the marks on the template to verify that the holes are in the proper locations. 3. After verifying that the 1/8" pilot holes are in the proper locations, use the 1/4" drill bit to enlarge the pilot holes. 4. Remove the template and replace it with the mounting plate on the floor over the drilled holes. 5. Place the 6 floor bolts through the mounting plate and into the holes just drilled. 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
NOTE:
Whenever unit
loading exceeds
3 Amperes, the unit power supply
will overload and automatically disconnect the power supply from
+12V DC
vehicle power at the cigarette lighter jack.
D.
Contents in Kit
TV and VCP Floor Console
Owner’s Manual
Remote Control
12V Cigarette Lighter Cord and Plug (for powering this unit)
Cardboard Mounting Template (for positioning the mounting holes on the floor)
Hardware Package for Securing Console to Vehicle Contains the following:
6 Floor Bolts
6 Sealing Washers
6 Fender Washers
6 Floor Nuts
2 Console Bolts
2 Spring Washers
1 Mounting Plate
E. Tools Required (not supplied)
Electric Drill
1/8” Steel Drill Bit
1/4” Steel Drill Bit
Socket Wrench Set with Deep-Wall, 7/16” Socket
Box Wrench, Size 7/16”
Standard Utility Knife (or Equivalent)
NOTE:
Two people are required for installation.
F. Installation Guide
(Refer to Figure 2)
1.
Temporarily place the cardboard mounting template on an appropriate
mounting location on the floor between driver/passenger seats, with the
rounded end of the template facing the front of your vehicle. Make sure
that you have checked both underneath the vehicle and within the vehicle
(under the carpet) for obstructions.
2.
Drill 6 small 1/8” pilot holes though the marks on the template to verify
that the holes are in the proper locations.
3.
After verifying that the 1/8” pilot holes are in the proper locations, use
the 1/4” drill bit to enlarge the pilot holes.
4.
Remove the template and replace it with the mounting plate on the floor
over the drilled holes.
5.
Place the 6 floor bolts through the mounting plate and into the holes just
drilled.
4