Audiovox EZCRG Owners Manual - Page 6

Refer

Get Audiovox EZCRG - Mini EZ Fit Console PDF manuals and user guides View all Audiovox EZCRG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

6. Place 1 sealing washer (rubber side towards vehicle floor) and 1 large fender washer over each of the floor bolts and attach the floor nuts. In addition to the sealing washer, it may be desirable to place a small circle of silicon sealer around the hole under the vehicle before installing the washers and nut, to further prevent moisture from getting into the vehicle. 7. Tighten the floor nuts down securely. Have the 2nd person inside the vehicle hold the floor bolts securely with the box-end wrench, while the person underneath the vehicle tightens down the floor nuts. 8. Press the latch of the door at the rear of the console to the right and open the door. Then set the console on the mounting plate, with the slot of the console base pointing to the tongue end of the mounting plate, and the two holes in the rear of the console pointing to the two holes in the upright end of the mounting plate. 9. Apply a firm push forward to mate the console base and the floor mounting plate, with the tongue of the mounting plate projecting into the slot of the console base. 10. Place the spring washer on the 2 console bolts. 11. Place the console bolts through the mounting plate and into the two holes at the rear of the console base. 12. Tighten the console base bolts with a Phillips screwdriver. G. Powering the unit (Refer to Figure 3) NOTE: Have all the wires, such as the power cord, AV cables and external antenna cable, or CATV cable, pass through the two notches at the bottom of the door. Plug the cigarette lighter cord into the 4-PIN DC input jack on the back of the console. Then reinstall the console rear door and press the latch to close the door. Plug the other end into the cigarette lighter receptacle in the vehicle. NOTE: If the unit draws in excess of 10 Amperes, the power supply will deactivate and turn off the unit. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
6.
Place 1 sealing washer (rubber side towards vehicle floor) and 1 large fender
washer over each of the floor bolts and attach the floor nuts.
In addition to
the
sealing washer,
it may be desirable to place a small circle of
silicon
sealer around the hole under the vehicle before installing the washers and
nut, to further prevent moisture from getting into the vehicle.
7.
Tighten the floor nuts down securely. Have the 2nd person inside the vehicle
hold the floor bolts securely with the box-end wrench, while the person
underneath the vehicle tightens down the floor nuts.
8.
Press
the latch of the door at the rear of the console to the right and open
the door.
Then set the console on the mounting plate, with the slot of the
console base pointing to the tongue end of
the mounting plate, and the two
holes in the rear of the console pointing to the two holes in the upright end of
the mounting plate.
9.
Apply a firm push forward to mate the console base and the floor mounting
plate, with the tongue of the mounting plate projecting into the slot of the
console base.
10. Place the spring washer on the 2 console bolts.
11. Place the console bolts through the mounting plate and into the two holes at
the rear of the console base.
12. Tighten the console base bolts with a Phillips screwdriver.
G.
Powering the unit
(Refer to Figure 3)
NOTE:
Have all the wires,
such as the power cord, AV cables and external
antenna cable, or CATV cable, pass through the two notches at
the
bottom of the door.
Plug the cigarette lighter cord into the 4-PIN DC input jack on the back of the
console. Then reinstall the console rear door and press
the latch to close the
door. Plug the other end into the cigarette lighter
receptacle in the vehicle.
NOTE:
If the unit draws in excess of 10 Amperes, the power
supply
will
deactivate and turn off the unit.
6