Avanti RIM49U3S-IS Instruction Manual - Page 10

Reversing the door swing

Get Avanti RIM49U3S-IS PDF manuals and user guides View all Avanti RIM49U3S-IS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Leveling the ice maker It is important for the icemaker to be leveled in order to work properly. It can be raised or lowered by rotating the plastic sheaths around each of the four feet on the bottom of the machine .If you find that the surface is not level, rotate the feet until the ice maker becomes level .You may need to make several adjustments to level it. We recommend using a carpenter's level to check the machine. 1. Place a carpenter's level on top of the product to see if the ice maker is level from front to back and side to side. 2. Adjust the height of the feet as follows: up Turn the leveling feet to the right to lower that side of the ice maker. Turn the leveling feet to the left to raise that side of the ice maker. down IMPORTANT: Once you are ready to install it in a cabinet or directly on the floor, you must adjust the feet to level the ice maker. If the floor is level, just revolve the two front feet to touch the floor. Reversing the door swing Tools needed: Flat head screwdriver, Phillips screwdriver IMPORTANT: Before you begin, unplug the ice maker or disconnect power. To remove door from hinges: 1. Remove top hinge cover by pushing it toward the back of the unit, then lifting it off. 2. Using a Phillips screwdriver, remove the screws, then remove the top hinge mat and top hinge. Keep the parts together and set them aside. 3. Lift the door off of the bottom hinge and set the door aside. To replace door on hinges: 1. Using a flathead screwdriver, remove the plug buttons from the screw holes opposite the door hinges, top and bottom. Set aside. 2. Remove the front louver. Set aside. 3. Remove the bottom hinge and place it on the opposite side at the bottom of the door. 4. Position the door on the bottom hinge. 5. Align the door on the bottom hinge and replace the top hinge and top hinge mat. 6. Replace top hinge cover by pressing it down over the hinge mat and then pushing it forward. 7. Push the plug buttons into the original screw holes. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
10
Leveling the ice maker
It is important for the icemaker to be leveled in order to
work properly. It can be raised or lowered by rotating
the plastic sheaths around each of the four feet on the
bottom of the machine .If you find that the surface is
not level, rotate the feet until the ice maker becomes
level .You may need to make several adjustments to
level it. We recommend using a carpenter’s level to
check the machine.
1.
Place a carpenter’s level on top of the product to see if
the ice maker is level from front to back and side to side.
2.
Adjust the height of the feet as follows:
Turn the leveling feet to the right to lower that side of the ice maker.
Turn the leveling feet to the left to raise that side of the ice maker.
IMPORTANT: Once you are ready to install it in a cabinet or directly on the floor, you must adjust the
feet to level the ice maker. If the floor is level, just revolve the two front feet to touch the floor.
Reversing the door swing
Tools needed:
Flat head screwdriver, Phillips screwdriver
IMPORTANT:
Before you begin, unplug the ice maker or disconnect power.
To remove door from hinges:
1.
Remove top hinge cover by pushing it toward the back of the unit, then lifting it off.
2.
Using a Phillips screwdriver, remove the screws, then remove the top hinge mat and top hinge.
Keep the parts together and set them aside.
3.
Lift the door off of the bottom hinge and set the door aside.
To replace door on hinges:
1. Using a flathead screwdriver, remove
the plug buttons from the screw holes
opposite the door hinges, top and
bottom. Set aside.
2.
Remove the front louver. Set aside.
3. Remove the bottom hinge and place it
on the opposite side at the bottom of the
door.
4.
Position the door on the bottom hinge.
5.
Align the door on the bottom hinge and
replace the top hinge and top hinge mat.
6. Replace top hinge cover by pressing it
down over the hinge mat and then
pushing it forward.
7. Push the plug buttons into the original
screw holes.
down
up