Avanti WCR506SS Instruction Manual - Page 9

Installation Instructions

Get Avanti WCR506SS PDF manuals and user guides View all Avanti WCR506SS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

INSTALLATION INSTRUCTIONS  BEFORE USING YOUR WINE CHILLER • Remove the exterior and interior packing. • Check to be sure you have all of the following parts: 1 Instruction Manual 5 Large Shelves 1 Short Shelf 2 Keys 1 Set Stainless Steel Hinges for Door Swing Reversal 2 Hinge Screw Caps 1 Stainless Steel Handle • Before connecting this appliance to the power source, let it stand upright for approximately 2 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation. • Clean the interior surface with lukewarm water using a soft cloth.  INSTALLATION OF YOUR WINE CHILLER • This appliance is designed to be for free standing installation or built-in (fully recessed). • Place your Wine Chiller on a floor that is strong enough to support it when it is fully loaded. To level your Wine Chiller, adjust the front leveling legs at the bottom of the Wine Chiller. • Locate the Wine Chiller away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Extreme cold ambient temperatures may also cause the unit not to perform properly. • Avoid locating the unit in moist areas. • Plug the Wine Chiller into an exclusive, properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician or an authorized Avanti Products service center.  BUILT - IN CABINET INSTRUCTIONS This unit is designed for both built-in or free standing installation. If you plan to use this unit in a built- in application please follow the requirements shown to the right. ← Figure shown Cabinet Opening Dimensions IN (min) MM (min) Width 24" 610 mm Depth 26" 661 mm Height 35" 889 mm → Figure shown Unit Dimensions IN (min) MM (min) Width Depth (with handle) Depth (without handle) 23 2/5" 24 2/5" 22 3/4" 595 mm 620 mm 575 mm Height 34 ¼" 870 mm 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
9
INSTALLATION INSTRUCTIONS
BEFORE USING YOUR WINE CHILLER
•
Remove the exterior and interior packing.
•
Check to be sure you have all of the following parts:
1
Instruction Manual
5
Large Shelves
1
Short Shelf
2
Keys
1 Set
Stainless Steel Hinges for Door Swing Reversal
2
Hinge Screw Caps
1
Stainless Steel Handle
•
Before connecting this appliance to the power source, let it stand upright for approximately 2
hours. This will reduce the possibility of a malfunction in the cooling system from handling
during transportation.
•
Clean the interior surface with lukewarm water using a soft cloth.
INSTALLATION OF YOUR WINE CHILLER
•
This
appliance is designed to be for free standing installation or built-in (fully recessed).
•
Place your Wine Chiller on a floor that is strong enough to support it when it is fully loaded. To
level your Wine Chiller, adjust the front leveling legs at the bottom of the Wine Chiller.
•
Locate the Wine Chiller away from direct sunlight and sources of heat (stove, heater, radiator,
etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical
consumption. Extreme cold ambient temperatures may also cause the unit not to perform
properly.
•
Avoid locating the unit in moist areas.
•
Plug the Wine Chiller into an exclusive, properly installed-grounded wall outlet. Do not under
any circumstances cut or remove the third (ground) prong from the power cord. Any questions
concerning power and/or grounding should be directed toward a certified electrician or an
authorized Avanti Products service center.
BUILT – IN CABINET INSTRUCTIONS
This unit is designed for both built-in or free standing installation.
If you plan to use this unit in a built-
in application please follow the requirements shown to the right.
←
Figure shown
Cabinet Opening Dimensions
IN (min)
MM (min)
Width
24”
610 mm
Depth
26”
661 mm
Height
35”
889 mm
Figure shown
→
Unit Dimensions
IN (min)
MM (min)
Width
23
2
/
5
”
595 mm
Depth
(with handle)
24
2
/
5
”
620 mm
Depth
(without handle)
22
3
/
4
”
575 mm
Height
34 ¼”
870 mm