Axis Communications M7016 M7016 Video Encoder - Installation Guide - Page 12

Access the Product, Reset to Factory Default Settings, Further Information

Get Axis Communications M7016 PDF manuals and user guides View all Axis Communications M7016 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

AXIS M7016 Video Encoder Connect the cables 1. Connect the video encoder to the network using a network cable RJ45. 2. Connect the cameras to the video inputs. 3. Connect the supplied indoor power adapter. 4. Check that the indicator LEDs indicate the correct conditions. See LED Indicators on page 8 NOTICE Make sure the unit is properly grounded by using the grounding screw. If the unit will be used with cameras or accessories located outdoors then its ground screw should be connected to a local grounding point. Access the Product Use the tools provided on the Installation and Management Software CD to assign an IP address, set the password and access the video stream. This information is also available from the support pages on www.axis.com/techsup/ Reset to Factory Default Settings Important Reset to factory default should be used with caution. A reset to factory default will reset all settings, including the IP address, to the factory default values. Note The installation and management software tools are available on the CD supplied with the product and from the support pages on www.axis.com/techsup To reset the product to the factory default settings: Note To reset a single channel to the original factory default settings, use the button provided in that unit's web interface. It is also possible to reset parameters to factory default via the web interface. Go to Setup > System Options > Maintenance. Further Information The User Manual is available at www.axis.com 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
AXIS M7016 Video Encoder
Connect the cables
1. Connect the video encoder to the network using a network cable RJ45.
2. Connect the cameras to the video inputs.
3. Connect the supplied indoor power adapter.
4. Check that the indicator LEDs indicate the correct conditions. See
LEDIndicatorson
page 8
NO
NO
NOTICE
TICE
TICE
Make sure the unit is properly grounded by using the grounding screw.
If the unit will be used with cameras or accessories located outdoors then its ground screw
should be connected to a local grounding point.
Access the Product
Use the tools provided on the Installation and Management Software CD to assign an IP address,
set the password and access the video stream. This information is also available from the support
pages on
www.axis.com/techsup/
Reset to Factory Default Settings
Important
Reset to factory default should be used with caution. A reset to factory default will reset
all settings, including the IP address, to the factory default values.
Note
The installation and management software tools are available on the CD supplied with the
product and from the support pages on
www.axis.com/techsup
To reset the product to the factory default settings:
Note
To reset a single channel to the original factory default settings, use the button provided in
that unit’s web interface.
It is also possible to reset parameters to factory default via the web interface. Go to
Setup
> System Options > Maintenance
.
Further Information
The User Manual is available at
www.axis.com
12