Behringer EURODESK SX2442FX Manual - Page 5

5 EURODESK SX3242FX/SX2442FX User Manual 1. Introduction FBQ Feedback Detection System One of the most outstanding features of this console is the FBQ Feedback Detection System, which is part of the graphic equalizer. This ingenious circuit makes it possible to detect and subsequently eliminate feedback frequencies very quickly. FBQ increases the brightness of the EQ fader LEDs for the frequency bands where feedback is occurring. What used to be a tedious search for feedback frequencies is now mere child's play. XENYX Mic Preamps The microphone channels feature high-end XENYX Mic Preamps that compare well with costly outboard preamps in terms of sound quality and dynamics and boast the following features: • 130 dB dynamic range for an incredible amount of headroom • A bandwidth ranging from below 10 Hz to over 200 kHz for crystal-clear reproduction of even the finest nuances • The extremely low-noise and distortion-free circuitry guarantees absolutely natural and transparent signal reproduction • They are perfectly matched to every conceivable microphone with up to 60 dB gain and +48 volt phantom power supply • They enable you to use the greatly extended dynamic range of your 24-bit/192-kHz HD recorder to the full, thereby maintaining optimal audio quality "British EQ" The equalizers used for the XENYX Series are based on the legendary circuitry of top-notch consoles made in Britain, which are renowned throughout the world for their incredibly warm and musical sound character. Even with extreme gain settings these equalizers ensure outstanding audio properties. What is more, the EURODESK comes with two effects processors using 24-bit A/D and D/A converters and the effects algorithms of our renowned 19" multi-effects device VIRTUALIZER PRO DSP2024P. Each processor offers 99 presets with first-class room simulations, delay and modulation effects as well as compressor, tube distortion and numerous other effects available-all with excellent audio quality! The mixer is equipped with a state-of-the-art integrated switch-mode power supply. Unlike conventional designs, this supply automatically adapts to supply voltages between 100 and 240 V. With its considerably higher efficiency, it is also more economical in terms of power consumption than standard power supply units. 1.1 Before you get started 1.1.1 Shipment Your product was carefully packed at the factory to ensure safe transport. Nevertheless, if the box is damaged inspect the unit immediately for signs of damage. ◊ If the unit is damaged please do NOT return it to us, but notify your dealer and the shipping company immediately; otherwise, claims for damage or replacement may not be granted. ◊ We recommend that you use a flight case to give the unit optimum protection during use or transport. ◊ Always use the original box to prevent damage during storage or transport. ◊ Make sure that children cannot play unsupervised with the unit or its packaging. ◊ Please ensure proper disposal of all packing materials. 1.1.2 Initial operation Ensure adequate air supply and to avoid overheating do not place the unit near radiators etc. ◊ Blown fuses must be replaced by fuses of the correct rating! Please refer to the "Specifications" section for the applicable rating. For connection to the mains use the enclosed power cord with cold connector which complies with the relevant safety regulations. ◊ Please make sure that all devices are properly grounded. For your own safety, never remove or disable the ground conductors from the devices or on the power cords. The unit must always be connected to the mains outlet with a protective grounding connection. ◊ We would like to point out that high volume levels may damage your hearing and/or your headphones/loudspeakers. To avoid switch-on/off thumps from the console and any downstream devices, always make sure that your power amp(s) or active speakers are the last components that are switched on and the first to be switched off. Always make sure that the appropriate volume is set. Important notes concerning installation ◊ The sound quality may diminish within the range of powerful broadcasting stations and high-frequency sources. Increase the distance between the transmitter and the device and use shielded cables for all connections. 1.1.3 Online registration Please register your new BEHRINGER equipment right after your purchase by visiting http://behringer.com and read the terms and conditions of our warranty carefully. Should your BEHRINGER product malfunction, it is our intention to have it repaired as quickly as possible. To arrange for warranty service, please contact the BEHRINGER retailer from whom the equipment was purchased. Should your BEHRINGER dealer not be located in your vicinity, you may directly contact one of our subsidiaries. Corresponding contact information is included in the original equipment packaging (Global Contact Information/European Contact Information). Should your country not be listed, please contact the distributor nearest you. A list of distributors can be found in the support area of our website (http://behringer.com). Registering your purchase and equipment with us helps us process your repair claims more quickly and efficiently. Thank you for your cooperation! 1.2 The manual This manual is designed to give you an overview of all control elements and at the same time inform you in detail about how to use them. To provide you with a clear structure, we have grouped the control elements according to their function. They can easily be found on the enclosed numbered illustrations. If you need more detailed information on specific topics, please visit our web site at behringer.com. The product-related information pages and the ULTRANETbased glossary explain the relevant audio engineering terminology in full detail.