Behringer UFX1204 Quick Start Guide - Page 8

14 XENYX UFX1204 XENYX UFX1204 Controls (EN) Step 2: Controls (1) XLR balanced input. (2) LINE/HI-Z input. (3) LINE/HI-Z button (Channels 1 & 2 only). When HI-Z mode is engaged, you can plug your guitar or bass into this input without using an external direct (D.I.) box. (4) +48 V Phantom power is used for condenser microphones that require between 9 V DC and 48 V DC power to operate. (5) LOW CUT button filters out frequencies below 80 Hz. (6) GAIN knob adjusts the sensitivity of the MIC and LINE/HI-Z inputs. (7) SEND lets you choose to route your input signal to FireWire/USB pre or post EQ. (8) COMP(RESSOR) knob adjusts the amount of compression effect on the channel. (9) EQ knobs adjust the HIGH, MID, and LOW frequencies of the channel. Adjust the FREQ knob to select the specific frequency adjusted by the MID knob. (10) EQ button turns the EQ section on and off. (11) AUX / FX knobs adjust how much of the channel's signal is sent to the AUX SEND jacks and/or the internal FX processor. (12) PAN knob positions the channel's signal in the stereo field. (13) MUTE button removes the channel from the MAIN MIX and sends it to the ALT 3-4 bus. (14) SOLO button sends the channel signal to the solo bus (Solo in Place) or to the PFL bus (Pre-Fader Listen). (15) LEVEL METER shows the input signal level of the channel's input signal. (16) CHANNEL FADER adjusts the channel volume. (17) LINE IN left and right input jacks for mono or stereo signals. (18) LINE/FW 1-2 (3-4) button allows the signal from a computer to be routed via FireWire/USB to these channels and controlled by the EQ and AUX and fader functions. NOTE: All FireWire (FW) routing switches work for USB connectivity to a computer and for the USB stand-alone mode depending on how you have the MODE selector switch (48) set. (19) 4-band EQ for the stereo channels. (20) BAL(ANCE) knob controls the relative volume of the left and right input signals before they are routed to the stereo main mix bus. (21) CONTROL ROOM OUT jacks carry the summed effects and main mix signals, as well as soloed channel signals. (22) MAIN OUT jacks for connecting line level signal to powered speakers or external amplifier. (23) ALT 3-4 OUT jacks for connecting line level signal of an alternate stereo mix to a recording device, powered speakers or external amplifier. Can also be used for subgrouping. (24) CD/TAPE IN and OUT for connecting a stereo source or for sending the main signal to an external recorder. (25) PHONES jacks for connecting headphones. (26) INPUT level meters display the signal input intensity going into the FX bus. (27) FX effect knob selects which effect is applied to the signal. (28) EDIT knob adjusts the effect's main parameter. (29) FX ON button turns the effect on and off. (30) The TAP/SELECT button performs two functions. Hit the button several times in the tempo of the music piece to adapt the delay time of presets 9 and 15 or the modulation speed of presets 10-12. The Button will start flashing in the corresponding tempo. The TAP/SELECT button also changes the characteristic of the second parameter on presets 1-8, 13-14 and 16. By pressing the button you can toggle between two different values (light off/on) for the second parameter. 15 Quick Start Guide (31) FW/USB LED indicates the computer is connected (based on the selection switch on back panel). (46) USB DRIVE jack for use with external USB hard disk drives (recommended) or thumb drives in STAND ALONE mode. (32) VU METER displays the MAIN OUTPUT signal level. (33) MODE button determines whether the SOLO button operates in "Solo in Place" (button out) or "Pre-Fader Listen" (button in). PFL is preferred for gain setting purposes. (47) USB jack for connecting to a computer. (48) MODE selector switch. (49) FireWire jack for connecting to a computer. (50) CHANNEL INSERTS allow you to connect external effects to the individual channels (1-4) PRE-FADER and PRE-EQ. (34) PHONES knob controls the volume level of the PHONES jacks. (51) MAIN OUTPUTS for sending MAIN MIX via balanced XLR cables. (35) CONTROL RM knob controls the volume of the (52) AUX(ILIARY) SENDS route the 2 auxiliary bus CONTROL ROOM OUT jacks. signals via balanced or unbalanced ¼" cables. (36) SOURCE monitoring select buttons route the signal to either the CONTROL RM/PHONES jacks (left column) or the MAIN MIX (right column). (37) PRE/POST fader select buttons for the AUX and FX SEND busses. (53) AUX(ILIARY) RETURNS allow you to bring a stereo effects signal routed from an AUX SEND jack, through a processor, back into the designated auxiliary bus. These inputs can also be used to connect additional line sources such as keyboards. (38) AUX SEND 1-2 knobs adjust the level from send busses 1-2 (rear panel), internal FX bus (AUX 2 only), and FW 13-14 channels for recording (post knob). (39) Destination routing switch for AUX RETURN 2 (to MAIN bus or AUX SEND 1 bus). (40) AUX RETURN 1-2 knobs adjust the level of AUX RETURN busses 1-2 (rear panel) or return signal from internal FX (AUX 2 only). (41) MUTE, SOLO, and output LEVEL knobs for ALT 3-4 bus. (42) TALKBACK MIC (Built-in), LEVEL knob (adjusts TALKBACK microphone volume), DESTINATION switches, and TALK button (press while talking). (43) 16 TRACK USB DRIVE RECORDER/MIDI TRANSPORT CONTROL for use while connected to a computer via FireWire or USB as a MIDI Machine Control. Also used in STAND ALONE MODE for controlling the internal USB recorder functions. (44) MAIN MIX stereo fader adjusts the overall output of the mixer. (45) POWER ON turns the mixer on.