Behringer ULTRATONE K900FX Manual - Page 6

Mains Connection, Fuse Holder/voltage Selector, Ground Lift, Line Out, Stereo Link, Sub Out, Foot Sw - keyboard amp

Get Behringer ULTRATONE K900FX PDF manuals and user guides View all Behringer ULTRATONE K900FX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

6 ULTRATONE K3000FX/K1800FX/K900FX/K450FX User Manual (15) MAINS CONNECTION. Use the power cord supplied with the unit to connect it to the mains. (16) FUSE HOLDER/VOLTAGE SELECTOR. Before connecting the unit to the mains, make sure that the voltage setting matches your local voltage. A blown fuse should only be replaced by a fuse of the same type and rating. On some units, the fuse holder can be switched to one of two positions, i.e. 230 V and 120 V. When operating the unit outside Europe at 120 V, a higher fuse rating is required. (17) The GROUND LIFT switch disconnects (switch pressed) the ground connection at the LINE OUT output to effectively eliminate hum noise resulting from ground loops (K3000FX and K1800FX only). (18) Use the balanced LINE OUT XLR connectors to feed the audio signal from your ULTRATONE to a mixing console (K3000FX and K1800FX only). The LINE OUT signal is post-EQ. (19) These are the LINE OUT outputs on 1/4" TS connectors (K900FX and K450FX: one 1/4" TS connector). ◊ Both XLR and 1/4" TS LINE OUT connectors can be used simultaneously. (20) For stereo operation the ULTRATONE features a STEREO LINK facility. You can connect the OUT of the ULTRATONE to the LINK IN of another keyboard amp that serves as slave to achieve true stereo sound. When using the ULTRATONE as slave, connect the LINK OUT of the master amp to the IN (K3000FX and K1800FX only). (21) The SUB OUT connector provides the line-level mono subwoofer signal for connection to the input of a power amp or active subwoofer. (22) Connect your footswitch to the FOOT SW jack, so as to activate/deactivate the effects processor. (23) Use the CD IN (K900FX and K450FX: AUX IN) connectors to connect the output of your CD player, tape deck, CD or MD walkman. This way you can play along to music or keyboard tutorial CDs. (24) These are the LINE inputs for channels 1 - 4 on 1/4" TS connectors. For mono input signals please use the L (MONO) connector. (25) Channel 1 is equipped with an additional XLR MIC input. Due to internal +15 V phantom power you can even use condenser microphones. Both XLR and 1/4" TS connectors can be used simultaneously. In this case the LEVEL control of channel 1 adjusts both the level of the LINE and MIC signal. (2) (4) (8) (10) (12) (14) (1) (3) Fig. 2.1: Front panel control elements (K3000FX and K1800FX) (16) (5) (6) (18) (19) (20) (7) (9) (11) (13) (24) (25) (15) (17) Fig. 2.2: Rear panel control elements (K3000FX and K1800FX) (21) (26)(22) (23)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
6
ULTRATONE K3000FX/K1800FX/K900FX/K450FX User Manual
(15)
MAINS CONNECTION
. Use the power cord supplied with the unit to connect
it to the mains.
(16)
FUSE HOLDER/VOLTAGE SELECTOR
. Before connecting the unit to the
mains, make sure that the voltage setting matches your local voltage.
A blown fuse should only be replaced by a fuse of the same type and rating.
On some units, the fuse holder can be switched to one of two positions,
i.e. 230 V and 120 V. When operating the unit outside Europe at 120 V,
a higher fuse rating is required.
(17)
The
GROUND LIFT
switch disconnects (switch pressed) the ground
connection at the LINE OUT output to effectively eliminate hum noise
resulting from ground loops (K3000FX and K1800FX only).
(18)
Use the balanced
LINE OUT
XLR connectors to feed the audio signal from
your ULTRATONE to a mixing console (K3000FX and K1800FX only). The LINE
OUT signal is post-EQ.
(19)
These are the
LINE OUT
outputs on °" TS connectors (K900FX and K450FX:
one °" TS connector).
◊
Both XLR and 1/4" TS LINE OUT connectors can be used simultaneously.
(20)
For stereo operation the ULTRATONE features a
STEREO LINK
facility.
You can connect the
OUT
of the ULTRATONE to the LINK IN of another
keyboard amp that serves as slave to achieve true stereo sound. When using
the ULTRATONE as slave, connect the LINK OUT of the master amp to the IN
(K3000FX and K1800FX only).
(21)
The
SUB OUT
connector provides the line-level mono subwoofer signal for
connection to the input of a power amp or active subwoofer.
(22)
Connect your footswitch to the
FOOT SW
jack, so as to activate/deactivate
the effects processor.
(23)
Use the
CD IN
(K900FX and K450FX: AUX IN) connectors to connect the
output of your CD player, tape deck, CD or MD walkman. This way you can
play along to music or keyboard tutorial CDs.
(24)
These are the
LINE
inputs for channels 1 - 4 on °" TS connectors. For mono
input signals please use the L (MONO) connector.
(25)
Channel 1 is equipped with an additional XLR
MIC
input. Due to internal
+15 V phantom power you can even use condenser microphones. Both XLR
and °" TS connectors can be used simultaneously. In this case the LEVEL
control of channel 1 adjusts both the level of the LINE and MIC signal.
(1)
(3)
(5)
(6)
(7)
(9)
(2)
(4)
(8)
(14)
(12)
(10)
(11)
(13)
Fig. 2.1: Front panel control elements (K3000FX and K1800FX)
(15)
(25)
(24)
(19)
(20)
(18)
(16)
(23)
(22)
(26)
(17)
(21)
Fig. 2.2: Rear panel control elements (K3000FX and K1800FX)