Behringer XENYX 1832FX Manual - Page 7
GRAPHIC 9-BAND EQUALIZER (1832FX only), LEVEL METER, Subgroups and main mix fader - mixer
View all Behringer XENYX 1832FX manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
ENGLISH 12 XENYX 1622FX/1832FX/2222FX/2442FX User Manual MAIN MIX The MAIN MIX switch sends the main mix to the CONTROL ROOM OUT and the PHONES output as well as to the level meter. PHONES/CTRL ROOM Use this control to adjust the control room output level and the headphones volume. CD/TAPE TO MAIN When the CD/TAPE TO MAIN switch is depressed, the 2-track input is routed to the main mix and thus serves as an additional input for tape machines. You can also connect MIDI instruments or other signals here that do not require any further processing. At the same time, this switch disables the main mix to tape output link. POWER The blue POWER LED indicates that the device is switched on. +48 V The red"+48 V"LED lights up when phantom power is switched on. Phantom power is required to operate condenser microphones. ◊ While phantom power is switched on, do not connect or disconnect microphones on the mixer (or the stagebox/wallbox). Connect any micro-phones before switching on phantom power. Additionally, monitor/ PA speakers should be muted before you activate the phantom power supply. After switching on, wait approx. one minute before adjusting the input gain so that the system has time to stabilize. LEVEL METER The high-precision level meters always give you an accurate display of signal level. LEVEL SETTING: When recording to digital recorders, the recorder's meter should not go into overload. This is because, unlike analog recordings, it takes only slightly excessive levels to create unpleasant digital distortion. When recording to analog, the VU meters of the recording machine should reach approx. +3 dB with low-frequency signals (e.g. kick drum). Due to their inertia, VU meters tend to display too low a signal level at frequencies above 1 kHz. You should only drive instruments such as a Hi-Hat as far as -10 dB. Snare drums should be driven to approx. 0 dB. ◊ The peak meters of your XENYX display level almost independent of frequency. A recording level of 0 dB is recommended for all types of signal. MODE The MODE switch determines whether the channels' SOLO switch operates as PFL (Pre Fader Listen) or as solo (Solo In Place). PFL (LEVEL SET) To activate the PFL function, press the MODE switch. The PFL function should, as a rule, be used for level setting (GAIN). The signal is sourced pre-fader and assigned to the mono PFL bus. In "PFL" mode, only the left side of the peak meter is in operation. A PFL'd channel should be driven to the 0 dB mark of the VU meter. SOLO (NORMAL) When the MODE switch is not depressed, the stereo solo bus is active. Solo is actually short for "Solo In Place". This is the customary method for listening to an individual signal or to a group of signals. As soon as a solo switch is pressed, all channels not solo selected are muted in th e monitor path (control room and phones). A channel's position in the stereo image is maintained. The solo bus carries the output signals of the channel pan controls, the aux sends and the stereo line inputs. On the 2442FX all aux returns, and on the 1832FX only aux return 2 can be routed to the solo bus. The solo bus is, as a rule, taken post-fader. ◊ The PAN control in the channel strip offers a constant power characteristic. This means that the signal is always at a constant level, irrespective of position in the stereo panorama. If the PAN control is moved fully left or right, the level in that channel increases by 4 dB. This ensures that, when set at the center of the stereo image, the audio signal does not appear louder. For this reason, with the solo function activated (Solo in Place), audio signals from channels with PAN controls that have not been moved fully left or right are displayed at a lower volume than in the PFL function. As a rule, solo signals are monitored via the control room outputs and headphones jack and are displayed by the level meters. If a solo switch is pressed, the signals from the tape input, the subgroups and the main mix are cut from these outputs and the level meter. MAIN SOLO The MAIN SOLO LED lights up as soon as a channel or aux send solo switch is pressed. The MODE switch must be set to "Solo". PFL (LEVEL SET) The PFL (LEVEL SET) LED indicates that the peak meter is set to PFL mode. XENYX 1622FX/1832FX/2222FX/2442FX User Manual 13 Fig. 2.17: PHONES jack 3. GRAPHIC 9-BAND EQUALIZER (1832FX only) PHONES jack You can connect headphones to this ¼" stereo jack (2442FX: 2 phones jacks). The signal routed to the PHONES connection is the same as that routed to the control room output. 2.3.11 Subgroups and main mix fader You use the high-precision quality faders to control the output level of the subgroups and the main mix. LEFT/RIGHT switch The switches located above the subgroup faders assign the subgroup signal either to the left or right side of the main bus. Similarly, it can be routed to both sides or none at all. In the latter case, the submix is present only at the corresponding subgroup outputs. XENYX2442FX Fig. 2.18: Subgroup and main mix faders XENYX1832FX Fig. 3.1: The graphic stereo equalizer of the 1832FX The graphic stereo equalizer allows you to tailor the sound to the room acoustics. EQUALIZER Use this switch to activate the graphic equalizer. MAIN MIX/MONITOR This toggles the graphic equalizer between the main mix and the monitor mix. With the switch up (not depressed), the equalizer is active in stereo on the main mix, and inactive on the monitor mix. When the switch is depressed the equalizer is active in mono on the monitor mix, and inactive on the main mix. FBQ FEEDBACK DETECTION The switch turns on the FBQ Feedback Detection System. It uses the LEDs in the frequency band faders to indicate the critical frequencies. On a per-need basis, lower the frequency range in question somewhat in order to avoid feedback. The graphic stereo equalizer has to be turned on in order to use this function. ◊ Logically, at least one (ideally several) microphone channels have to be open for feedback to occur at all! Feedback is particularly common when stage monitors ("wedges") are concerned, because monitors project sound in the direction of microphones. Therefore, you can also use the FBQ Feedback Detection for monitors by placing the equalizer in the monitor bus (see MAIN MIX/MONITOR). ENGLISH