Beko HRZG64120 User Manual - Page 15

conversion

Page 15 highlights

Gas conversion ' DANGER: A •ll Before starting any work on the gas installation, disconnect the gas supply. There is the risk of explosion! In order to change your appliance's gas type, change all injectors and make flame adjustment for all valves at reduced flow rate position. Exchange of injector for the burners 1. Take off burner cap and burner body. 2. Unscrew injectors by turning the counter- clockwise. 3. Fit new injectors. 4. Check all connections for secure fitting and tightness. New injectors have their position marked on their packing or injector table on Injector table, page 10 can be referred to. » The normal length of a straight flame in the reduced position should be 6-7 mm. 4. If the flame is higher than the desired position, turn the screw clockwise. If it is smaller turn anticlockwise. 5. For the last control, bring the burner both to high-flame and reduced positions and check whether the flame is on or off. Depending on the type of gas tap used in your appliance the adjustment screw position may vary. 00 00 2 3 4 1 Flame failure device 2 Spark plug 3 Injector 4 Burner Unless there is an abnormal condition, do not attempt to remove the gas burner taps. ou must call an Authorised service agent if it is necessary to change the taps. Reduced gas flow rate setting for hob taps 1. Ignite the burner that is to be adjusted and turn the knob to the reduced position. 2. Remove the knob from the gas tap. 3. Use an appropriately sized screwdriver to adjust the flow rate adjustment screw. For LPG (Butane - Propane) turn the screw clockwise. For the natural gas, you should turn the screw counter-clockwiseonce. Flow rate adjustment screw 00 00 \ Flow rate adjustment screw f the gas type of the unit is changed, then he rating plate that shows the gas type of he unit must also be changed. 15/EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24

Gas
conversion
A
'
DANGER:
ll
Before
starting
any
work
on
the
gas
installation,
disconnect
the
gas
supply.
There
is
the
risk
of
explosion!
In
order
to
change
your
appliance's
gas
type,
change
all
injectors
and
make
flame
adjustment
for
all
valves
at
reduced
flow
rate
position.
Exchange
of
injector
for
the
burners
1
.
Take
off
burner
cap
and
burner
body.
2.
Unscrew
injectors
by
turning
the
counter-
clockwise.
3.
Fit
new
injectors.
4.
Check
al
l
connections
for
secure
fitting
and
tightness.
New
injectors
have
their
position
marked
on
their
packing
or
injector
table
on
Injector
table,
page
10
can
be
referred
to.
2
3
4
1
Flame
failure
device
2
Spark
plug
3
Injector
4
Burner
Unless
there
is
an
abnormal
condition,
do
not
attempt
to
remove
the
gas
burner
taps.
ou
must
call
an
Authorised
service
agent
if
it
is
necessary
to
change
the
taps.
Reduced
gas
flow
rate
setting
for
hob
taps
1
.
Ignite
the
burner
that
is
to
be
adjusted
and
turn
the
knob
to
the
reduced
position.
2.
Remove
the
knob
from
the
gas
tap.
3.
Use
an
appropriately
sized
screwdriver
to
adjust
the
flow
rate
adjustment
screw.
For
LPG
(Butane
-
Propane)
turn
the
screw
clockwise.
For
the
natural
gas,
you
should
turn
the
screw
counter-clockwiseonce.
»
The
normal
length
of
a
straight
flame
in
the
reduced
position
should
be
6-7
mm.
4.
If
the
flame
is
higher
than
the
desired
position,
turn
the
screw
clockwise.
If
it
is
smal
ler
turn
anticlockwise.
5.
For
the
last
control,
bring
the
burner
both
to
high
-flame
and
reduced
positions
and
check
whether
the
flame
is
on
or
off.
Depending
on
the
type
of
gas
tap
used
in
your
appliance
the
adjustment
screw
position
may
vary.
00
00
Flow
rate
adjustment
screw
00
00
Flow
rate
adjustment
screw
\
f
the
gas
type
of
the
unit
is
changed,
then
he
rating
plate
that
shows
the
gas
type
of
he
unit
must
also
be
changed.
15/EN