Beko WMC1471 User Manual - Page 12

Connecting to the drain, 6 Adjusting the feet

Get Beko WMC1471 PDF manuals and user guides View all Beko WMC1471 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Installation 3.5 Connecting to the drain • The end of the drain hose must be directly connected to the wastewater drain or to the washbasin. • Drain hose shall be attached to a wall drain, stand pipe or sink siphon connected to the foul water drain, do not connect to surface water drains. A warning: Your house will be flooded if the hose comes out of its housing during water discharge. Moreover, there is risk of scalding due to high washing temperatures! To prevent such situations and to ensure smooth water intake and discharge of the machine, fix the end of the discharge hose tightly so that it cannot come out. • The hose should be attached to a height of at least 40 cm, and 100 cm at most. • In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet. Therefore, follow the heights described in the figure. • If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak. 3.6 Adjusting the feet A warning: In order to ensure that the product operates more silently and vibration-free, it must stand level and balanced on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its place and cause crushing and vibration problems. 1. Loosen the lock nuts on the feet by hand. 2. Adjust the feet until the product stands level and balanced. 100cm 40cm 3. Tighten all lock nuts again by hand. • To prevent flowing of dirty water back into the machine and to allow for easy discharge, do not immerse the hose end into the dirty water or do not drive it in the drain more than 15 cm. If it is too long, cut it short. • The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched between the drain and the machine. A warning: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged. 12 / EN Washing Machine / User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
12 / EN
Washing Machine / User‘s Manual
Installation
3.5 Connecting to the drain
• The end of the drain hose must be directly
connected to the wastewater drain or to the
washbasin.
• Drain hose shall be attached to a wall drain,
stand pipe or sink siphon connected to the
foul water drain, do not connect to surface
water drains.
A
WARN±NG:
Your house will be
flooded if the hose comes out of
its housing during water discharge.
Moreover, there is risk of scalding
due to high washing temperatures!
To prevent such situations and to
ensure smooth water intake and
discharge of the machine, fix the
end of the discharge hose tightly so
that it cannot come out.
• The hose should be attached to a height of at
least 40 cm, and 100 cm at most.
• In case the hose is elevated after laying
it on the floor level or close to the ground
(less than 40 cm above the ground), water
discharge becomes more difficult and the
laundry may come out excessively wet.
Therefore, follow the heights described in
the figure.
100cm
40cm
• To prevent flowing of dirty water back into
the machine and to allow for easy discharge,
do not immerse the hose end into the dirty
water or do not drive it in the drain more than
15 cm. If it is too long, cut it short.
• The end of the hose should not be bent, it
should not be stepped on and the hose must
not be pinched between the drain and the
machine.
• If the length of the hose is too short, use it
by adding an original extension hose. Length
of the hose may not be longer than 3.2 m.
To avoid water leak failures, the connection
between the extension hose and the drain
hose of the product must be fitted well with
an appropriate clamp as not to come off and
leak.
3.6 Adjusting the feet
A
WARN±NG:
In order to ensure that
the product operates more silently
and vibration-free, it must stand
level and balanced on its feet.
Balance the machine by adjusting
the feet. Otherwise, the product
may move from its place and cause
crushing and vibration problems.
1. Loosen the lock nuts on the feet by hand.
2. Adjust the feet until the product stands level
and balanced.
3. Tighten all lock nuts again by hand.
A
WARN±NG:
Do not use any tools to
loosen the lock nuts. Otherwise,
they will get damaged.