BenQ 0.6 Wall Mount Wall Mount User Manual - Page 6

Installation Steps

Get BenQ 0.6 Wall Mount PDF manuals and user guides View all BenQ 0.6 Wall Mount manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

English Installation Steps 1. Installing the wall bracket A A. Make sure the wall bracket (O) is in the correct position on the wall. Hold the bracket (O) firmly against the wall and mark the places for the holes with a pencil. Drill the holes at the marked points. The holes for a masonry wall should be 10mm (0.39") in diameter and 55mm deep (2.17"). Use a hammer to drive the plastic plugs (B) into the holes. For a wooden wall, drill 4.5mm (0.17") diameter holes 55m (2.17") deep. B. Fasten the bracket to the wall with the self-tapping screws (C) provided. B C. Push the power cord into the front end of the projector main support member and pull it out at the back. D. Insert and secure the hex socket cap screw M6 x L8 (E) in the holes of the projector main support member (P) and the wall bracket (O) by using a 5mm hex wrench (K). It is O necessary to leave a gap of 0.5mm for adjustment of the angle after assembly. E. Before positioning the hinge module (A), secure the socket head screw (G) in the projector main support member (P) to enable the cantilever support to be in the horizontal direction. 1. 2. Installing the fixing bracket on the bottom A of the projector A. Place the hinge module (A) on the projector. Use the height adjustment collars (I) and the screws with fixed washers (H) to fasten the module firmly to the projector. B. Align the holes in the hinge connector (D) with those in the hinge module (A). Insert M6 x 12 (F) socket head screws into the holes and tighten them with the 5mm hex wrench (K). Allow 2-3mm clearance for installing the bracket on the arm. 2. 3. Installing the bracket on the bottom of the A projector arm A. Assemble the hinge module (A) and the projector main support member (P). B. After this use the hex wrench (K) to fasten them securely. 3. 4. Cable Management A A. Plug the power cord into the projector. B. Fit the plastic cap (L) to the end of the projector main support member (P). C. Pass the power cord through the lower plastic cover (N) and then fit the upper (M) and lower (N) plastic covers as shown. C C B D C E P A B H I 0.5mm E E G D F B P A B L M M N 7 Installation Steps 4.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
7
Installation Steps
English
Installation Steps
L
B
C
D
E
1.
2.
3.
4.
C
H
D
F
A
O
B
A
B
A
A
I
M
N
M
B
C
B
A
P
E
E
G
0.5mm
P
A
1. Installing the wall bracket
A. Make sure the wall bracket (O) is in the correct position
on the wall. Hold the bracket (O) firmly against the wall
and mark the places for the holes with a pencil.
Drill the holes at the marked points. The holes for a
masonry wall should be 10mm (0.39”) in diameter and
55mm deep (2.17”). Use a hammer to drive the plastic
plugs (B) into the holes.
For a wooden wall, drill 4.5mm (0.17”) diameter holes
55m (2.17”) deep.
B. Fasten the bracket to the wall with the self-tapping screws
(C) provided.
C. Push the power cord into the front end of the projector
main support member and pull it out at the back.
D. Insert and secure the hex socket cap screw M6 x L8 (E) in
the holes of the projector main support member (P) and
the wall bracket (O) by using a 5mm hex wrench (K). It is
necessary to leave a gap of 0.5mm for adjustment of the
angle after assembly.
E.
Before positioning the hinge module (A), secure the
socket head screw (G) in the projector main support
member (P) to enable the cantilever support to be in the
horizontal direction.
2. Installing the fixing bracket on the bottom
of the projector
A. Place the hinge module (A) on the projector. Use the
height adjustment collars (I) and the screws with fixed
washers (H) to fasten the module firmly to the projector.
B. Align the holes in the hinge connector (D) with those in
the hinge module (A). Insert M6 x 12 (F) socket head
screws into the holes and tighten them with the 5mm hex
wrench (K). Allow 2-3mm clearance for installing the
bracket on the arm.
3. Installing the bracket on the bottom of the
projector arm
A.
Assemble the hinge module (A) and the projector main
support member (P).
B.
After this use the hex wrench (K) to fasten them securely.
4. Cable Management
A. Plug the power cord into the projector.
B. Fit the plastic cap (L) to the end of the projector main
support member (P).
C. Pass the power cord through the lower plastic cover (N)
and then fit the upper (M) and lower (N) plastic covers as
shown.