BenQ DS660 User Guide - Page 6

Introduction

1

BenQ DX/S660

DX/S650 User’s Guide

INTRODUCTION

Caution

TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER –SER-

VICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL. PLEASE READ THIS USER’S GUIDE BEFORE YOU OPER-

ATE YOUR PROJECTOR. SAVE THIS USER’S GUIDE FOR FUTURE REF-

ERENCE .

Safety Instructions

1.

Read this user’s guide before you operate your projector and save it for future

reference.

2.

The lamp becomes extremely hot during operation. Allow the projector to cool for

approximately 45 minutes prior to removing the lamp assembly for replacement.

Do not operate lamps beyond the rated lamp life. Excessive operation of lamps

beyond the rated life could cause them to explode on rare occasions.

3.

Never replace the lamp assembly or any electronic components unless the

projector is unplugged.

4.

To reduce the risk of electric shock, do not disassemble this appliance. Take it to a

qualified technician when service or repair is required. Incorrect reassembly can

cause electric shock when the appliance is subsequently used.

5.

Do not place this product on an unstable cart, stand, or table. The product may fall,

sustaining serious damage.

6.

This product is capable of displaying inverted images for ceiling mount installation.

Please use suitable equipment for mounting the unit and ensure it is securely

installed.

Caution

•

Always open the lens shutter or remove the lens cap when the projector

lamp is on.

•

Do not look straight at the projector lens during operation. The intense

light beam may damage your eyes.

•

In some countries, the line voltage is NOT stable. This projector is

designed to operate safely within a bandwidth of 110 to 2

4

0 volts, but

could fail if power cuts or surges of more than10 volts occur. In these

high-risk areas, it is recommended that a power stabilizer unit be used in

conjuction with this projector.

Save this user’s guide: The information contained in this manual will assist you in operating

and maintaining your personal projector.

Section	Page
BenQ	1
Copyright	2
Disclaimer	2
Fill this in!!	2
Introduction	6
1. Read this user’s guide before you operate your projector and save it for future reference.	6
2. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately...	6
3. Never replace the lamp assembly or any electronic components unless the projector is unplugged.	6
4. To reduce the risk of electric shock, do not disassemble this appliance. Take it to a qualifie...	6
5. Do not place this product on an unstable cart, stand, or table. The product may fall, sustaini...	6
6. This product is capable of displaying inverted images for ceiling mount installation. Please u...	6
1. Macintosh adapter	8
2. 210W Lamp module	8
1. Lift the projector up and press the adjuster button to release the adjuster.	11
2. The adjuster will drop into position and be locked.	11
Installation	14
HDTV description	14
Connecting to Various Equipment	15
Operation	16
1. Plug the power cord into a wall socket.	16
2. Turn on the main power switch.	16
3. Press POWER to start the unit. The back-lit POWER key flashes green and stays green when the p...	16
4. Switch on all connected equipment.	16
1. Press POWER and a warning message will appear. To turn off the projector, press POWER again.	24
2. The fan will continue to run for approximately two minutes.	24
3. Turn off the main power switch.	24
4. Disconnect the power cord from the wall socket.	24
Maintenance	25
1. Press the POWER button to switch off the projector. Disconnect the power cord from the outlet ...	26
2. Loosen the screw and remove the lamp cover. If the lamp is hot, avoid burns by waiting 45 minu...	26
3. Loosen the 3 screws. (It is strongly recommended that you use a magnetic- head screwdriver.) P...	26
4. Replace the lamp with a new one. Insert it into the projector, and tighten the screws firmly. ...	26
5. Re-install the lamp cover and tighten the screw. Do not turn on the power with the lamp cover ...	26
OSD	27
FUNCTION	27
1. The internal temperature is too high.	27
2. The fans are not working.	27
Troubleshooting	29
Specifications	31
Technical Specifications	31
Resolution	32
H Sync (kHz)	32
V Sync (Hz)	32
Remark	32
640x350	32
31.5	32
70.1	32
640x400	32
37.9	32
85.1	32
VESA	32
720x400	32
31.5	32
70.0	32
720x400	32
37.9	32
85.1	32
VESA	32
640x480	32
31.5	32
60.0	32
VESA	32
640x480	32
37.9	32
72.8	32
VESA	32
640x480	32
35	32
66.7	32
Macintosh	32
640x480	32
43.3	32
85.0	32
VESA	32
800x600	32
35.2	32
56.3	32
VESA	32
800x600	32
37.9	32
60.3	32
VESA	32
800x600	32
46.9	32
75.0	32
VESA	32
800x600	32
48.1	32
72.2	32
VESA	32
800x600	32
53.7	32
85.1	32
VESA	32
832x624	32
49.7	32
74.5	32
Macintosh	32
1024x768	32
48.4	32
60.0	32
VESA	32
1024x768	32
56.5	32
70.1	32
VESA	32
1024x768	32
60.0	32
75.0	32
VESA	32
1024x768	32
68.7	32
85.0	32
VESA	32
1280x1024	32
64.0	32
60.0	32
VESA	32

BenQ DS660 User Guide - Page 6

Introduction - replacement lamp

Page 6 highlights