BenQ MP522 User Manual - Page 30

Correcting keystone, Magnifying and searching for details

Get BenQ MP522 - XGA DLP Projector PDF manuals and user guides
UPC - 840046019570
View all BenQ MP522 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps. • Using the remote control Press / on the projector or remote control to display the Keystone correction page. Press to correct keystoning at the top of the image. Press to correct keystoning at the bottom of the image. • Using the OSD menu 1. Press Menu/Exit and then press / until the DISPLAY menu is highlighted. 2. Press to highlight Keystone and press Mode/Enter. The Keystone correction page displays. 3. Press to correct keystoning at the top of Press / . the image or press to correct keystoning at the bottom of the image. Press / . Magnifying and searching for details If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture. • Using the remote control 1. Press Digital Zoom +/- to display the Zoom bar. 2. Press Digital Zoom + to magnify the center of the picture. Press the key repeatedly until the picture size is suitable for your need. 3. Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture. 4. To restore the picture to its original size, press AUTO. You can also press Digital Zoom -. When the key is pressed again, the picture is further reduced until it is restored to the original size. • Using the OSD menu 1. Press Menu/Exit and then press / until the DISPLAY menu is highlighted. 2. Press to highlight Digital Zoom and press Mode/Enter. The Zoom bar displays. 3. Repeat steps 2-4 in the section of "Using the remote control" above. Or if you are using the projector control panel, continue to the following steps. 4. Press on the projector repeatedly to magnify the picture to a desired size. 5. To navigate the picture, press Mode/Enter to switch to the paning mode and press the directional arrows ( , , , ) to navigate the picture. 30 Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
Operation
30
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of the projector, you will need to manually
correct it following one of these steps.
•
Using the remote control
Press
/
on the projector or remote control
to display the Keystone correction page. Press
to correct keystoning at the top of the image. Press
to correct keystoning at the bottom of the
image.
•
Using the OSD menu
1.
Press
Menu/Exit
and then press
/
until
the
DISPLAY
menu is highlighted.
2.
Press
to highlight
Keystone
and press
Mode/Enter
. The
Keystone
correction page
displays.
3.
Press
to correct keystoning at the top of
the image or press
to correct keystoning
at the bottom of the image.
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the
direction arrow keys for navigating the picture.
•
Using the remote control
1.
Press
Digital Zoom +/-
to display the Zoom
bar.
2.
Press
Digital Zoom +
to magnify the center of
the picture. Press the key repeatedly until the
picture size is suitable for your need.
3.
Use the directional arrows (
,
,
,
) on
the projector or remote control to navigate the
picture.
4.
To restore the picture to its original size, press
AUTO
. You can also press
Digital Zoom -
. When the key is pressed again, the picture is
further reduced until it is restored to the original size.
•
Using the OSD menu
1.
Press
Menu/Exit
and then press
/
until the
DISPLAY
menu is highlighted.
2.
Press
to highlight
Digital Zoom
and press
Mode/Enter
. The Zoom bar displays.
3.
Repeat steps 2-4 in the section of
"Using the remote control"
above. Or if you are using
the projector control panel, continue to the following steps.
4.
Press
on the projector repeatedly to magnify the picture to a desired size.
5.
To navigate the picture, press
Mode/Enter
to switch to the paning mode and press the
directional arrows (
,
,
,
) to navigate the picture.
Press
/
.
Press
/
.