BenQ PB8263 User Manual - Page 30

Operation, Start up

Get BenQ PB8263 - XGA DLP Projector PDF manuals and user guides
UPC - 840046016098
View all BenQ PB8263 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Operation Start up 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). 2. Remove the lens cap. If it is left on, it could become deformed due to the heat produced by the projection lamp. 3. Turn the main power switch on. The Power indicator lights orange. 4. Press and hold (for 2 seconds) I Power on the remote control or projector to start the projector. The Power indicator light flashes green and stays green when the projector is on. The start up procedure takes about 30 seconds after pressing I Power. In the later stage of start up, a default BenQ logo is projected. 5. Switch all of the connected equipment on. 6. The projector will start to search for input signals. The current input source being scanned displays in the lower right corner of the screen. The search will continue until an input source signal is detected. You can also press SOURCE on the projector or remote control to select your desired input signal. For more information, refer to "Switching input signal" on page 31. If the frequency/ resolution of the input signal exceeds the projector's operating range, you will see the message "Out of Range" displayed on a blank screen. Please change to an input signal which is compatible with the projector's resolution. See "Timing chart" on page 58 for details. 30 Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
Operation
30
Operation
Start up
1.
Plug the power cord into the projector and into a wall
socket. Turn on the wall socket switch (where fitted).
2.
Remove the lens cap. If it is left on, it could become
deformed due to the heat produced by the projection
lamp.
3.
Turn the main power switch on. The
Power
indicator
lights orange.
4.
Press and hold (for 2 seconds)
Power
on
the remote control or projector to start the
projector. The
Power indicator light
flashes
green and stays green when the projector is on.
The start up procedure takes about 30 seconds
after pressing
Power
. In the later stage of
start up, a default BenQ logo is projected.
5.
Switch all of the connected equipment on.
6.
The projector will start to search for input
signals. The current input source being
scanned displays in the lower right corner of
the screen. The search will continue until an
input source signal is detected.
You can also press
SOURCE
on the projector or remote control to select your desired
input signal. For more information, refer to
"Switching input signal" on page 31
.
If the frequency/ resolution of the input signal exceeds the projector's operating range, you
will see the message “Out of Range” displayed on a blank screen. Please change to an input
signal which is compatible with the projector's resolution. See
"Timing chart" on page 58
for
details.
I