BenQ SH910 SH910 User Manual - Page 75

Timing of replacing the lamp, Status, Message

Get BenQ SH910 PDF manuals and user guides View all BenQ SH910 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Timing of replacing the lamp When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. Go to http://lamp.benq.com for a replacement lamp. The Lamp indicator light will light up if the lamp becomes too hot. See "Indicators" on page 79 for details. The following lamp warning displays will remind you to change the lamp. The warning messages below are for reference only. Please follow the actual on-screen instructions to prepare and replace the lamp. Status Message Install a new lamp for optimal performance. If the projector is normally run with Economic selected ("Setting Lamp Mode as Economic" on page 74), you may continue to operate the projector until the next lamp warning appears. Press MODE/ENTER to dismiss the message. A new lamp should be fitted to avoid the inconvenience when the projector runs out of lamp time. Press MODE/ENTER to dismiss the message. It is strongly recommended that you replace the lamp at this stage. The lamp is a consumable item. The lamp brightness diminishes with use. This is normal lamp behavior. You can replace the lamp whenever you notice that the brightness level has significantly diminished. Press MODE/ENTER to dismiss the message. The lamp MUST be replaced before the projector will operate normally. Press MODE/ENTER to dismiss the message. "XXXX" shown in the above messages are numbers that vary depending on different models. Maintenance 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
Maintenance
75
Timing of replacing the lamp
When the
Lamp indicator
lights up red or a message appears suggesting it is time to replace
the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
Go to
for a replacement lamp.
The Lamp indicator light will light up if the lamp becomes too hot. See
"Indicators" on page 79
for details.
The following lamp warning displays will remind you to change the lamp.
The warning messages below are for reference only. Please follow the actual on-screen
instructions to prepare and replace the lamp.
"XXXX" shown in the above messages are numbers that vary depending on different models.
Status
Message
Install a new lamp for optimal performance. If the
projector is normally run with
Economic
selected
(
"Setting Lamp Mode as Economic" on page 74
),
you may continue to operate the projector until
the next lamp warning appears.
Press
MODE/ENTER
to dismiss the message.
A new lamp should be fitted to avoid the
inconvenience when the projector runs out of
lamp time.
Press
MODE/ENTER
to dismiss the message.
It is strongly recommended that you replace the
lamp at this stage. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished.
Press
MODE/ENTER
to dismiss the message.
The lamp MUST be replaced before the projector
will operate normally.
Press
MODE/ENTER
to dismiss the message.