Biostar M6VCG M6VCG user's manual - Page 81

Network card I/O address

Get Biostar M6VCG PDF manuals and user guides View all Biostar M6VCG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

Chapter 4 Trouble Shooting No power to monitor. Monitor not connected to computer. Network card I/O address conflict. Memory problem, display card jumpers not set correctly. Computer virus. Check the power connectors to monitor and to system. Make sure monitor is connected to display card, change I/O address on network card if applicable. See instructions above. See instructions above. Reboot computer. Reinstall memory, make sure that all memory modules are installed in correct sockets. Check jumper and switch settings on display card. See display card section for information on settings. Use anti-virus programs (mcAfee, E-Prot, etc) to detect and clean viruses. 4-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
Chapter 4
Trouble Shooting
4-6
!"ÈÇ#$¾
¾ÁÊ¿¿Âµ¼!µ=ÀºÂ-²
²¹(ȺÈ.̼ ¼ ±º³´Ì
¸ËºÁ2(´Ë´
´(.³/Ë(2
No power to monitor.
Check the power
connectors to monitor and
to system. Make sure
monitor is connected to
display card, change I/O
address on network card if
applicable.
Monitor not connected to
computer.
See instructions above.
Network card I/O address
conflict.
See instructions above.
!"ÈÇ#$¾
²¹(ȺÈ.̼ ¼ ±º³´Ì
¸ËºÁ2(´Ë´
´(.³/Ë(2
Memory problem, display
card jumpers not set
correctly.
Reboot computer.
Reinstall memory, make
sure that all memory
modules are installed in
correct sockets. Check
jumper and switch
settings on display card.
See display card section
for information on
settings.
Computer virus.
Use anti-virus programs
(mcAfee, E-Prot, etc) to
detect and clean viruses.