Biostar M7VKE M7VKE user's manual - Page 52

IR Function Duplex

Get Biostar M7VKE PDF manuals and user guides View all Biostar M7VKE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Chapter2 BIOS Setup Onboard FDD Controller Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and if you wish to use it. If install and FDC or the system has no floppy drive, select Disabled in this field. The Choices: Enabled (default), Disabled. Onboard Serial Port 1 Select an address and corresponding interrupt for the serial port. The Choices: Disabled, Auto (default), 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3. Onboard IR Port Select an address and corresponding interrupt for the IR port. The Choices: Enabled, Disabled (default). UART 2 Mode This item allows you to determine which Infra Red (IR) function of the onboard I/O chip, you wish to use. The Choices: HPSIR (default), ASKIR. IR Function Duplex This item allows you to determine which Infra Red (IR) function of onboard I/O chip. The Choices: Half (default), Full. TX, RX inverting enable This item allows you to determine the active of Tx, Rx. The Choices: No/No, No/Yes (default), Yes/No, Yes/Yes. Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I/O address. The Choices: Disable, 3BC/IRQ7, 378/IRQ7 (default), 278/IRQ5 Onboard Parallel Mode Select an operating mode for the onboard parallel (printer) port. Select Normal unless you are certain your hardware and software both support EPP or ECP mode. The Choices: Normal (default), EPP (Enhanced Parallel Port), ECP (Extended Capabilities Port), ECP/EPP 2-20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
Chapter2
BIOS Setup
2-20
Onboard FDD Controller
Select Enabled if your system has a floppy disk controller (FDC) installed on the
system board and if you wish to use it. If install and FDC or the system has no
floppy drive, select Disabled in this field.
The Choices: Enabled
(default), Disabled.
Onboard Serial Port 1
Select an address and corresponding interrupt for the serial port.
The
Choices:
Disabled,
Auto
(default), 3F8/IRQ4, 2F8/IRQ3,
3E8/IRQ4, 2E8/IRQ3.
Onboard IR Port
Select an address and corresponding interrupt for the IR port.
The Choices:
Enabled,
Disabled
(default).
UART 2 Mode
This item allows you to determine which Infra Red (IR) function of the onboard
I/O chip, you wish to use.
The Choices:
HPSIR
(default), ASKIR.
IR Function Duplex
This item allows you to determine which Infra Red (IR) function of onboard I/O
chip.
The Choices:
Half
(default), Full.
TX, RX inverting enable
This item allows you to determine the active of Tx, Rx.
The Choices:
No/No,
No/Yes
(default), Yes/No, Yes/Yes.
Onboard Parallel Port
This item allows you to determine access onboard parallel port controller with
which I/O address.
The Choices:
Disable, 3BC/IRQ7,
378/IRQ7
(default), 278/IRQ5
Onboard Parallel Mode
Select an operating mode for the onboard parallel (printer) port. Select Normal
unless you are certain your hardware and software both support EPP or ECP
mode.
The Choices:
Normal
(default), EPP (Enhanced Parallel Port),
ECP (Extended Capabilities Port), ECP/EPP