Biostar MCP6P3 Setup Manual - Page 3

Introduction - n68s3

Get Biostar MCP6P3 PDF manuals and user guides View all Biostar MCP6P3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

CHAPTER 1: INTRODUCTION MCP6P3/N68S3 1.1 BEFORE YOU START Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below: Prepare a dry and stable working environment with sufficient lighting. Always disconnect the computer from power outlet before operation. Before you take the motherboard out from anti-static bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge. Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board. Do not leave any unfastened small parts inside the case after installation. Loose parts will cause short circuits which may damage the equipment. Keep the computer from dangerous area, such as heat source, humid air and water. The operating temperatures of the computer should be 0 to 45 degrees Celsius. 1.2 PACKAGE CHECKLIST IDE Cable X 1(optional) Serial ATA Cable X 2 Rear I/O Panel for ATX Case X 1 Installation Guide X 1 Fully Setup Driver CD X 1 (full version manual files inside) FDD Cable X 1 (optional) Serial ATA Power Cable X 1 (optional) USB 2.0 Cable X1 (optional) S/PDIF out Cable X 1 (optional) Note: The package contents may be different due to area or your motherboard version. 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
MCP6P3/N68S3
1
CHAPTER 1: INTRODUCTION
1.1
B
EFORE
Y
OU
S
TART
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
±
Prepare a dry and stable working environment with
sufficient lighting.
±
Always disconnect the computer from power outlet
before operation.
±
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
±
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
±
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
±
Keep the computer from dangerous area, such as heat
source, humid air and water.
±
The operating temperatures of the computer should be
0 to 45 degrees Celsius.
1.2
P
ACKAGE
C
HECKLIST
z
IDE Cable X 1(optional)
z
Serial ATA Cable X 2
z
Rear I/O Panel for ATX Case X 1
z
Installation Guide X 1
z
Fully Setup Driver CD X 1 (full version manual files inside)
z
FDD Cable X 1 (optional)
z
Serial ATA Power Cable X 1 (optional)
z
USB 2.0 Cable X1 (optional)
z
S/PDIF out Cable X 1 (optional)
Note:
The package contents may be different due to area or your motherboard version.