Biostar U8598 U8598 user's manual - Page 49

Windows NT4, Installing Drivers During Windows NT 4.0 Installation

Get Biostar U8598 PDF manuals and user guides View all Biostar U8598 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Mainboard Features Windows NT4 Installing Drivers During Windows NT 4.0 Installation 1. Start the system installation by booting from the Windows NT disk: a) Floppy install: boot the system with the FastTrak 376 driver diskette. b) Floppyless install: boot from floppy and type "WINNT /B". After files have been copied, the system will reboot. On the reboot, press the "F6" key when the message "Setup is inspecting your computer's hardware configuration..." appears. c) CD-ROM disk install: boot from the CD-ROM disk and press the "F6" key when the message "Setup is inspecting your computer's hardware configuration..." appears. 2. When the "Windows NT Setup" window is generated, press "S" to Specify an Additional Device(s). 3. Press "O" to select "Other" and press the "Enter" key. 4. Insert the FastTrak 376 driver diskette into drive A: and press the "Enter" key. 5. Choose "Win NT Promise FastTrak 376 (tm) Controller" from the list that appears on screen, then press the "Enter" key. 6. The Windows NT Setup screen will appear again saying "Setup will load support for the following mass storage devices:" The list will include "Win NT Promise FastTrak 376 (tm) controller". NOTE: If you need to specify any additional devices to be installed, do so at this time. Once all devices are specified, continue to step 7. 7. From the Windows NT Setup screen, press the Enter key. Setup will now load all device files and then continue the Windows NT installation. 8. After a successful installation, the "SCSI Adapter Setup" box will show that the "Win NT Promise FastTrak 376 (tm) Controller" driver has been installed. 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Mainboard Features
46
Windows NT4
Installing Drivers During Windows NT 4.0 Installation
1.
Start the system installation by booting from the Windows NT disk:
a)
Floppy install: boot the system with the FastTrak 376 driver diskette.
b)
Floppyless install: boot from floppy and type “WINNT /B”. After files have
been copied, the system will reboot. On the reboot, press the “F6” key
when the message “Setup is inspecting your computer’s hardware
configuration…” appears.
c)
CD-ROM disk install: boot from the CD-ROM disk and press the “F6” key
when the message “Setup is inspecting your computer’s hardware
configuration…” appears.
2.
When the “Windows NT Setup” window is generated, press “S” to Specify an
Additional Device(s).
3.
Press “O” to select “Other” and press the “Enter” key.
4.
Insert the FastTrak 376 driver diskette into drive A: and press the “Enter” key.
5.
Choose “Win NT Promise FastTrak 376 (tm) Controller” from the list that
appears on screen, then press the “Enter” key.
6.
The Windows NT Setup screen will appear again saying “Setup will load
support for the following mass storage devices:” The list will include “Win NT
Promise FastTrak 376 (tm) controller”.
NOTE
:
If you need to specify any additional devices to be installed, do so at
this time. Once all devices are specified, continue to step 7.
7.
From the Windows NT Setup screen, press the Enter key. Setup will now load
all device files and then continue the Windows NT installation.
8.
After a successful installation, the “SCSI Adapter Setup” box will show that the
“Win NT Promise FastTrak 376 (tm) Controller” driver has been installed.