Bissell Proheat 2X Pet 1391V User Guide - Page 11

Deep Reach Tool attachment, Cleaning with the Stain Trapper Tool Attachment

Get Bissell Proheat 2X Pet | 1391V PDF manuals and user guides View all Bissell Proheat 2X Pet | 1391V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Operations Deep Reach Tool attachment (Select models only) 3. 1. Follow the instructions on page 7 for filling the 2-in-1 water tank and the formula tank. 2. Follow instructions 3-6 on page 10 under "Cleaning with attachments". 3. Set tool on stain and press the trigger to spray solution onto the area to be cleaned. 5. 4. Slowly move the tool back and forth over the soiled surface, keeping the tool in contact with the carpet. 5. Release trigger and move tool slowly over the soiled area to suction up water and dirt. 7. 6. Continue to clean the area, working in small sections, until no more dirt can be removed. 7. Remove tool from hose when finished. Clean under warm water before storing. Cleaning with the Stain Trapper Tool Attachment (Select models only) 1. Attach the Stain Trapper tool to the end of the hose. 2. Gently scrape up any semi-solids with a spoon or spatula. Do not use a knife or other utensil with sharp edges because it could damage the carpet or upholstery. 3. Plug in and turn on the power switch. 4. Clean by pressing the trigger to spray solu- tion onto the area to be cleaned. Slowly move the tool back and forth over the soiled surface. Release the trigger to suction soiled water. Continue to clean in the area, working in small sections, until no more dirt can be removed. Rinse (optional) and suction as needed. CAUTION: Do not overwet. 5. NOTE: Do not fill the Stain Trapper tank above the FULL line. 5. To empty the Stain Trapper tool, rotate the small tank on the bottom of the tool to unlock it. NOTE: Be careful to keep the top of the tool facing upward or soiled water will spill out of the tank. 7. 6. Dump dirty water into a sink or toilet and rinse the tank out with clean water. Replace the tank by lining up the "unlock" symbol with the small arrow on the tank and turning it to the "lock" symbol. 7. Clean the front of the tool by removing the plate over the suction path. Pull down on the bottom of the plate to remove. Run the tool and the plate under clean water to rinse taking care to remove all debris. Replace the front plate by sliding it back into place. www.BISSELL.com 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
Operati´s
Deep Reach Tool attachment
(Select models only)
1.
Follow the instructions on page 7 for filling the
2-in-1 water tank and the formula tank.
2.
Follow instructions 3-6 on page 10 under
“Cleaning with attachments”.
3.
Set tool on stain and press the trigger to spray
solution onto the area to be cleaned.
4.
Slowly move the tool back and forth over the
soiled surface, keeping the tool in contact with
the carpet.
5.
Release trigger and move tool slowly over the
soiled area to suction up water and dirt.
6.
Continue to clean the area, working in small
sections, until no more dirt can be removed.
7.
Remove tool from hose when finished. Clean
under warm water before storing.
Cleaning with the Stain Trapper Tool Attachment
(Select models only)
1.
Attach the Stain Trapper tool to the end
of the hose.
2.
Gently scrape up any semi-solids with a spoon
or spatula. Do not use a knife or other utensil
with sharp edges because it could
damage the carpet or upholstery.
3.
Plug in and turn on the power switch.
4.
Clean by pressing the trigger to spray solu-
tion onto the area to be cleaned. Slowly move
the tool back and forth over the soiled surface.
Release the trigger to suction soiled water.
Continue to clean in the area, working in small
sections, until no more dirt can be removed.
Rinse (optional) and suction as needed.
CAUTION: Do not overwet.
NOTE: Do not fill the Stain Trapper tank
above the FULL line.
5.
To empty the Stain Trapper tool, rotate
the small tank on the bottom of the tool
to unlock it.
NOTE: Be careful to keep the top of the tool
facing upward or soiled water will spill out of
the tank.
6.
Dump dirty water into a sink or toilet and
rinse the tank out with clean water. Replace
the tank by lining up the “unlock” symbol with
the small arrow on the tank and turning it to
the “lock” symbol.
7.
Clean the front of the tool by removing the
plate over the suction path. Pull down on the
bottom of the plate to remove. Run the tool
and the plate under clean water to rinse taking
care to remove all debris. Replace the front
plate by sliding it back into place.
www.BISSELL.com
11
3.
5.
7.
7.
5.