Bosch B18ID80SRS Installation Instructions - Page 24

Important, Caution

Get Bosch B18ID80SRS PDF manuals and user guides View all Bosch B18ID80SRS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

7. Attaching an alternative antiĆtip device ! IMPORTANT NOTE ! If possible, always screw the wooden beam to existing studs on the rear panel of the cavity. If the antiĆtip brackets cannot be attached securely, an alternative antiĆtip device can be attached. However, ensure that there is no play between the appliance and the antiĆtip device. q Saw the wooden beam (cross section min. 3" x 4") to the required length. Length is equal to the width of the installation cavity! i Note - If the installation cavity is deeper than the appliance, select a beam which has a larger cross section or attach 2 beams. - The beam must cover the appliance by at least 2" (50.8 mm). q Locate wall studs near the rear panel of the cavity and mark drill holes in the beam. q Predrill the wooden beam. q Attach the wooden beam to the rear panel of the cavity. 8. Preparing to connect the water (only for appliances which require a water connection) d CAUTION d Turn off the main water tap to prevent damage caused by leaking water. q Attach the connecting pipe to the shutĆoff valve according to the instructions supplied by the manufacturer of the ice maker installation kit. q Install the connecting pipe. Always observe the indicated gap dimensions to prevent damage to the connecting pipe when pushing in the appliance. q Attach the connecting pipe to the floor with adhesive tape. q Mark the installation height (lower edge of the beam) on the rear panel of the cavity. q Select screws according to the thickness of the wooden beam: length = min. 2.5 x beam thickness, diameter #12 or #14. i Specify the number of screws according to the cavity width, thereby ensuring that the beam can be attached securely. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
24
7.
Attaching
an
alternative
antiĆtip
device
!
IMPORTANT
NOTE
!
If
possible,
always
screw
the
wooden
beam
to
existing
studs
on
the
rear
panel
of
the
cavity.
If the
antiĆtip
brackets
cannot
be
attached
securely,
an±alternative
antiĆtip
device
can
be
attached.
However,
ensure
that there
is
no play
between
the
appliance
and
the
antiĆtip
device.
q
Saw
the
wooden
beam
(cross
section
min.
3"
x 4")
to
the
required
length.
Length
is
equal
to
the
width
of
the
installation
cavity!
i
Note
-
If the
installation
cavity
is
deeper
than
the
appliance,
select
a
beam
which
has
a
larger
cross
section
or
attach
2
beams.
-
The
beam
must
cover
the
appliance
by
at
least
2"
(50.8
mm).
q
Mark
the
installation
height
(lower
edge
of
the
beam)
on
the
rear
panel
of
the
cavity.
q
Select
screws
according
to
the
thickness
of
the
wooden
beam:
length
=
min.
2.5
x
beam
thickness,
diameter
#12
or
#14.
i
Specify
the
number
of
screws
according
to
the
cavity
width,
thereby
ensuring
that
the
beam
can
be±attached
securely.
q
Locate
wall
studs
near
the
rear
panel
of
the
cavity
and
mark
drill
holes
in
the beam.
q
Predrill
the
wooden
beam.
q
Attach
the
wooden
beam
to
the
rear
panel
of
the
cavity.
8.
Preparing to
connect
the
water
(only for
appliances
which
require
a
water
connection)
d
CAUTION
d
Turn
off
the
main
water
tap
to
prevent
damage
caused
by leaking
water.
q
Attach
the
connecting
pipe
to
the shutĆoff
valve
according
to
the
instructions
supplied
by
the
manufacturer
of
the ice
maker
installation
kit.
q
Install
the
connecting
pipe.
Always
observe
the
indicated
gap
dimensions
to
prevent
damage
to
the
connecting
pipe
when
pushing
in the
appliance.
q
Attach
the connecting
pipe
to
the
floor
with
adhesive
tape.