Bosch DVR16E2302 Installation Instructions - Page 37

Ethernet connection

Get Bosch DVR16E2302 PDF manuals and user guides View all Bosch DVR16E2302 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Divar | Installation Manual | Hardware setup Ethernet connection The standard RJ-45 Ethernet socket is used to connect the unit directly to a PC or to a network. The Ethernet is also used to connect to an ATM/POS bridge unit. To connect directly to a network hub, use a straight-through network cable. To connect directly to a PC, use the supplied cross-over network cable. Consult with your local IT personnel for the specific type of cable needed. The cable length from node to node is limited to 100 feet (30.5 meters) maximum length and 6 feet (1.8 meters) minimum length. Network configuration The Divar is delivered with the DHCP function switched on, so IP addresses are assigned automatically if the network server uses DHCP. (Refer to the System settings/Connectivity/Network setup menu.) Specifications Connection: Differential signal voltage: Port details: Cable length: Impedance: Indicators: 10/100 BaseT, IEEE 802.3 ± 2.8V max, inputs have transient overvoltage protection. IEEE 802.3/802.3u - 100Base-TX/10Base-T physical layer. Auto Negotiation: 10/100, Full / Half Duplex 100 Meters: 100 Ohm unshielded twisted pair cable, category 3/4/5. 100 Meters: 150 Ohm shielded twisted pair cable. In-built compensation for impedance matching. ACT, 10, 100 LAN - RJ-45 Ethernet socket Signal Name: LAN_TX+ LAN_TXLAN_RX+ N/C N/C LAN_RXN/C N/C Pin no. 1 2 3 4 5 6 7 8 Description Ethernet transmit line plus Ethernet transmit line minus Ethernet Receive line plus No Connection No Connection Ethernet receive line minus No Connection No Connection 81 EN | 4-5 Panel view Bosch Security Systems

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Bosch Security Systems
Divar
| Installation Manual | Hardware setup
EN
| 4-5
Ethernet connection
The standard RJ-45 Ethernet socket is used to connect the unit directly to a PC
or to a network. The Ethernet is also used to connect to an ATM/POS bridge
unit. To connect directly to a network hub, use a straight-through network cable.
To connect directly to a PC, use the supplied cross-over network cable. Consult
with your local IT personnel for the specific type of cable needed. The cable
length from node to node is limited to 100 feet (30.5 meters) maximum length
and 6 feet (1.8 meters) minimum length.
Network configuration
The Divar is delivered with the DHCP function switched on, so IP addresses are
assigned automatically if the network server uses DHCP.
(Refer to the System
settings/Connectivity/Network setup menu.)
Specifications
Connection:
10/100 BaseT, IEEE 802.3
Differential signal voltage:
± 2.8V max, inputs have transient overvoltage
protection.
Port details:
IEEE 802.3/802.3u - 100Base-TX/10Base-T physical
layer.
Auto Negotiation: 10/100, Full / Half Duplex
Cable length:
100 Meters: 100 Ohm unshielded twisted pair cable,
category 3/4/5.
100 Meters: 150 Ohm shielded twisted pair cable.
Impedance:
In-built compensation for impedance matching.
Indicators:
ACT, 10, 100
LAN - RJ-45 Ethernet socket
Signal Name:
Pin no.
Description
LAN_TX+
1
Ethernet transmit line plus
LAN_TX-
2
Ethernet transmit line minus
LAN_RX+
3
Ethernet Receive line plus
N/C
4
No Connection
N/C
5
No Connection
LAN_RX-
6
Ethernet receive line minus
N/C
7
No Connection
N/C
8
No Connection
8
1
Panel view