Home » Bosch Manuals » Ranges » Bosch HII8055U » Manual Viewer

Bosch HII8055U Instructions for Use - Page 51

Fixing Malfunctions

Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Cookware Why is it taking so long for the cookware to heat up or why is it not heating up sufficiently despite being on a high heat setting? The cookware is too small for the element that is turned on or it is not suitable for induction cooking. Check that the cookware is suitable for induction cooking and that it is placed on the element that best corresponds to its size. You can find information on the type, size and positioning of cookware in the sections on ~ "Cooking with Induction". Cleaning How do I clean the cooktop? Using a special glass-ceramic cleaning agent produces the best results. We advise against using harsh or abrasive cleaning agents, dishwater detergent (concentrated) or scouring pads. You can find more information about cleaning and caring for your cooktop in the section on "Cleaning and Maintenance-Cooktop." Fixing Malfunctions Malfunctions are usually due to small details. Before calling the Customer Support, you should consider the following advice and warnings. 9 CAUTION Repairs should only be done by an authorized servicer. Improper repair of your appliance may result in risk of severe physical injury or death. Display Possible cause Solution None The power supply has been discon- Use other electrical devices to check whether a nected. short-circuit has occurred in the power supply. The device has not been connected in Ensure that the device has been connected in accordance with the connection dia- accordance with the connection diagram. gram. Electronics error. If the error cannot be eliminated, inform the technical after-sales service. The displays flash The Ù indicator flashes in the element displays "ƒ "... "† + heat setting and acoustic signal "† and acoustic signal ",/"‡ "‰ The control panel is damp or an object is covering it. Dry the control panel or remove the object. An error has occurred in the electron- To confirm the error, cover the control panel with ics. your hand. The electronics have overheated and Wait until the electronics have cooled down have switched off the corresponding sufficiently. Then touch any symbol on the cooktop. element. The electronics have overheated and have switched off all elements. There is a hot pan in the area of the Remove the pan. The error display goes out shortly control panel. There is a risk that the afterwards. You can continue to cook. electronics will overheat. There is a hot pan in the area of the Remove the pan. Wait for a few seconds. Touch control panel. To protect the electron- any control. If the error display goes out, you can ics, the element has been switched continue to cook. off. The element has overheated and Wait until the electronics have cooled down switched itself off to protect the work sufficiently and switch the element on again. surface. The element was operating for an The automatic safety switch-off function has been extended period without interruption. activated. See section "Automatic time limitation" Do not place hot pans on the control panel. 51

Section	Page
Induction Ranges	1
Table of ContentsUse and care manual	3
Safety Definitions	4
9 WARNING	4
9 CAUTION	4
NOTICE:	4
Note:	4
IMPORTANT SAFETY INSTRUCTIONS	5
READ AND SAVE THESE INSTRUCTIONS	5
WARNING	5
Proper Installation and Maintenance	5
WARNING	5
TIP OVER HAZARD	5
WARNING	5
WARNING	5
WARNING	5
WARNING	5
Fire Safety	6
WARNING	6
WARNING	6
WARNING	6
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A GREASE FIRE, OBSERVE THE FOLLOWING:	6
a. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.	6
b. NEVER PICK UP A FLAMING PAN – You may be burned.	6
c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.	6
d. Use an extinguisher ONLY if:	6
Burn Prevention	6
CAUTION	6
Electromagnetic Interference	7
WARNING	7
This induction cooktop generates and uses ISM frequency energy that heats cookware by using an electromagnetic field. It has been tested and complies with Part 18 of the FCC Rules for ISM equipment. This induction cooktop meets the FCC requirements t...	7
CAUTION	7
WARNING	7
Hazard due to magnetism	7
Child Safety	7
CAUTION	7
Cleaning Safety	7
WARNING	7
Risk of burns	7
Notes	7
Cookware Safety	7
Notes	7
CAUTION	8
WARNING	8
Risk of injury	8
WARNING	8
danger of injury	8
State of California Proposition 65 Warnings	8
WARNING	8
Note:	8
1. Providing good ventilation when cooking with gas.	8
2. Providing good ventilation during and immediately after self-cleaning the oven.	8
3. Operating the unit according to the instructions in this manual.	8
Food Safety	8
CAUTION	8
a. DO NOT use a warming drawer to heat cold food. It is safe to use the drawer to crisp crackers, chips or dry cereal and to warm plates.	8
b. Be sure to maintain proper food temperature. The USDA recommends holding hot food at 140°F or warmer.	8
c. DO NOT warm food for longer than one hour.	8
Causes of Damage	9
9 WARNING	9
risk of injury	9
NOTICES	9
Protecting the Environment	10
Saving Energy	10
Getting Started	11
Parts	11
Range Features	11
Retained Heat	11
Hot Surface Indicator	11
Oven Features	12
Cooling Fan	12
Convection Fan	12
Oven Bottom	12
9 WARNING	12
Oven Vent	12
Automatic Shutoff	12
Self-cleaning	12
Indicators and Other Features	12
Accessories	12
Inserting Racks	12
9 CAUTION	12
Flat Rack	13
1. Grasp rack firmly on both sides.	13
2. Insert rack (see picture).	13
3. Tilt rack up to allow stop into rack guide.	13
4. Bring rack to a horizontal position and push the rest of the way in.	13
1. Grasp rack firmly on both sides and pull rack toward you.	13
2. When the stop is reached, tilt rack up and pull the rest of the way out.	13
Telescopic Rack	13
1. Slide the rack in evenly until the rear of the rack is about two (2) inches from the back of the oven.	13
2. Tilt the front of the rack up about 3/4” (A) and finish pushing the rack all the way back (B).	13
Note:	13
3. The back of the telescopic rack drops in to place.	13
4. Pull the rack forward to engage the bottom of the rack onto the rear of the rack position guide.	13
5. Lower the front of the rack to finish seating it on the rack guide. The rack should feel stable when properly seated.	13
6. Slide the movable part of the telescopic rack in and out a few times to make sure it is able to move freely and that the non-moving part of the telescopic rack is securely anchored.	13
9 CAUTION	13
1. Lift the front of the telescopic rack assembly about 1/2” and push the rack to the rear about 3/4”. This allows the rack to disengage from the rack position guide.	13
2. Lift the rear of the telescopic rack assembly so it clears the rack position guide and gently pull the rack from the oven.	13
Note:	13
Before Using the Appliance for the First Time	14
Getting familiar with the appliance	14
Control panel	14
Touch control zone	14
Notes	14
The elements	15
Residual heat indicator	15
Operation	15
Main power switch	15
Turning the cooktop on	15
Turning the cooktop off	15
Note:	15
Setting the cooktop	15
Setting the element	15
Selecting the heat level	15
1. Select the desired element with by touching the $ symbol on the control panel. In the element display ‹ and the __ indicator light up.	15
2. Within the following 10 seconds, set the desired power level using the number keys.	15
3. To change the power level, select the element and set the desired power level using the number keys. To set an intermediate level touch the û symbols between the number keys.	15
Turning off the element	15
Notes	15
Recommendations	16
Settings table	16
9 CAUTION	16
Cook time	17
9 CAUTION	17
Setting a cook time	17
1. Select the desired element and power level.	17
2. Touch the Timer key. The x indicator lights up in the element display and ‹‹ is shown in the timer display.	17
3. Whithin 10 seconds enter the desired cook time using the number keys.	17
AutoChef®	17
Changing or canceling cook time	17
1. Select the desired element and touch the Timer key.	17
2. Adjust the cook time using the number keys. To cancel cook time set the timer to ‹‹.	17
Once the cook time has elapsed	17
Notes	17
Automatic timer	18
Note:	18
Kitchen timer	18
Setting the kitchen timer	18
1. Touch the Timer key until the V indicator lights up. ‹‹ and min appear on the timer display.	18
2. Set the desired time using the number keys.	18
Changing or deleting the time	18
When the time has elapsed	18
SpeedBoost® function	18
Limitation on use	18
Activation	18
1. Select an element.	18
2. Touch the Speed Boost key. › lights up on the display.	18
Deactivation	18
1. Select the element on which SpeedBoost® is set.	18
2. Touch the Speed Boost key. › goes out on the display and the element switched back to heat setting Š.	18
Note:	18
AutoChef®	18
Advantages when frying	18
9 CAUTION	18
Suitable pans for AutoChef®	18
9 CAUTION	19
Frying levels	19
Frying chart	19
Setting the AutoChef® feature	20
1. Select the element.	20
2. Touch the AutoChef key. The ‘ lights up on the element display.	20
3. Select the desired frying level using the number keys. The s symbol lights up on the display. The selected frying level is displayed.	20
4. Add the frying oil to the pan, then add the ingredients. Turn the food over as usual to avoid burning.	21
Turning off AutoChef®	21
Panel lock	21
Turning the panel lock on	21
Turning the panel lock off	21
9 CAUTION	21
Automatic panel lock	21
Wipe Protection	21
Notes	21
Automatic time limitation	21
Basic settings	21
--------	22
1. Turn on the cooktop with the main switch.	22
2. Within10 seconds, touch the Timer key for about 4 seconds.	22
3. Touching the Timer key again takes you to the basic settings.	22
4. Touch Timer repeatedly until the indicator for the desired function appears in the element display.	22
5. Select the desired setting using the number keys.	22
6. Touch Timer again for 4 seconds. The setting is stored.	22
Quit basic settings	22
Cooking with Induction	23
Advantages of induction cooking	23
Cookware	23
Unsuitable cookware	23
Properties of the base of the cookware	23
No pan or improper size	23
Empty pans or pans with a thin base	23
Pan detection	23
Cleaning and Maintenance-Cooktop	24
Daily Cleaning	24
Notes	24
Cleaning the Cooktop	24
9 WARNING	24
do not touch surface units or areas near units	24
9 CAUTION	24
Precautions for Long Life and Good Appearance of the Surface	24
9 WARNING	24
risk of burns	24
1. Clean the surface when it is completely cool with glass ceramic cooktop cleaner.	24
2. Wipe off spatters with a clean, damp sponge or a paper towel. Rinse and dry. Use white vinegar if smudge remains; rinse.	24
3. Apply a small amount of the glass ceramic cooktop cleaner. When dry, buff surface with a clean paper towel or cloth.	24
9 WARNING	24
risk of injury	24
Cleaning guidelines	25
Avoid these cleaners	25
Cleaning charts	25
Risk of injury	25
Maintenance	26
Operation-Oven	26
Oven Control Panel	26
Note:	26
Button Descriptions	26
Display Symbols	27
About the Oven	27
Basic Features	28
Setting the Clock	28
1. The oven must be in Standby mode (oven is powered on, but no cooking mode or timer in operation).	28
2. To access the clock set mode:	28
3. Use the numeric keypad to enter the desired time. Each number pressed is entered at the right and moving previously entered digits to the left. To set “12:45 pm”, press 1,2,4,5.	28
4. When the desired time is entered, set the time by pressing Enter.	28
Setting the Cooking Mode and Temperature	28
1. Press the desired Cooking Mode button. The cooking mode and default temperature are displayed. The temperature flashes to show it can be edited.	28
2. Press Enter to start the mode using the default temperature.	28
3. To change the temperature, enter the new temperature using the numeric buttons. For example, changing temperature to 375°. Press Enter to set the updated temperature.	28
Note:	28
4. Preheating starts.	28
Note:	28
1. Press the numeric keys to enter the desired temperature setting. The temperature entered is displayed beside the current time.	28
2. Select a cooking mode that is compatible with the temperature entered. If no cooking mode is selected within 5 seconds of setting the temperature, an error tone sounds and a “SELECT MODE” message is displayed and blinks.	28
3. Press a Mode Selection button to select a cooking mode.	29
Note:	29
1. Press the Cooking Mode button.	29
2. The current temperature flashes. Use the numeric buttons to enter a new temperature. Press Enter.	29
Temperature	29
in °F	29
Temperature	29
in °C	29
Max. Time Allowed without Activity	29
100-200	29
30-120	29
24 hours	29
201-550	29
121-300	29
12 hours	29
Timer	29
1. Press the Kitchen Timer On/Off button.	29
2. Press Enter.	29
3. When the kitchen timer has counted down to zero an alarm tone sounds every 10 seconds for 2 minutes and the message “TIMER END” is displayed.	29
Note:	29
1. Press the Kitchen Timer On/Off button.	29
2. The current time value blinks and can be edited.	29
Note:	30
1. Press Oven Timer button.	30
2. Select mode, press Enter.	30
3. When the timer reaches :00 the cooking mode ends and the message “OVEN TIMER FINISHED” is displayed. The oven alarm tone sounds every 10 seconds for 2 minutes.	30
1. If the oven timer is running and the time remaining needs to be changed, enter the oven timer mode by pressing the Oven Timer button	30
2. The temperature blinks, indicating it can be edited. Input a new temperature or press Enter for no change.	30
3. The timer value blinks, indicating it can be edited. Input the new time and restart the timer by pressing the Enter button.	30
Fast Preheat	30
1. Press Fast Preheat.	30
2. Press Start.	30
Special Features	30
Probe	30
Note:	31
1. Insert the probe into the meat as described above. The probe symbol is displayed.	31
2. Connect the probe to the oven. If the probe is not connected to the oven prior to starting Probe mode, an error tone sounds and the message “INSERT PROBE” is displayed.	31
3. Set the cooking mode and temperature.	31
4. The Set Probe Temp screen is displayed. A three digit input prompt “- - -” blinks in the lower right corner. Use the numeric keypad to enter the desire probe temperature and press Enter.	31
Note:	31
5. The probe current temperature and target temperature are both displayed in the format “105/180” at the lower right corner of the display. The actual temperature will display <80 until the food temperature reaches 80°F.	31
6. When the probe temperature reaches the set temperature, the cooking mode turns off. The current time is displayed and the message “COOKING COMPLETE” blinks at the bottom left of the display. An alarm tone sounds every 10 seconds for 2 minutes.	31
Notes	31
Sabbath Mode	32
1. Begin a Bake operation. While Bake is running, press and hold the Oven Timer button for 5 seconds.	32
2. Press Enter to accept the default 74:00 hours and start Sabbath Mode or use the numeric keypad to enter the desired Sabbath Mode timer value. Timer values between 0:01 and 74:00 can be entered.	32
Note:	32
3. Once Sabbath Mode has begun, the display changes to show the message “SABBATH ON”.	32
4. After the Sabbath Mode countdown reaches zero, the oven displays the current time and the message “SABBATH”. No changes can be made at this point. To end the Sabbath Mode and return to normal function, press the Oven Clear/Off button.	32
Notes	32
1. Press the Bake button.	32
2. Enter the new desired set temperature.	32
3. Press Enter.	32
Panel Lock	33
1. To enable Panel Lock, press and hold the Panel Lock button for 3 seconds (in Standby mode).	33
2. To disable Panel Lock, press and hold the Panel Lock button for 3 seconds. The display returns to Standby mode.	33
Settings	33
1. Press the Settings button.	33
2. The fist setup item is displayed. The display shoes “SET CLOCK”. Press Settings again to access the settings menu.	33
3. To display a different setup item, press the number corresponding to that setting (see table following or press the Settings button to cycle through available options).	33
4. To change the value for the displayed setting, press the Enter button to enter the edit mode. Use the numeric keypad to change the setting value. The corresponding setting value is shown in the table following.	33
Oven Temperature Offset	33
Note:	33
Settings Menu Options	33
Getting the Most Out of Your Appliance	34
General Tips	34
Pan Placement	34
Rack Position	34
Aluminum Foil	34
9 WARNING	34
Preheating the Oven	34
Preheat Reminders	34
For Best Results	34
Baking Pans and Dishes	35
Opening the Oven Door	35
High Altitude Baking	35
Condensation	35
Temperature Range by Cooking Mode	35
Mode	35
Lowest	35
Highest	35
100	35
550	35
100	35
550	35
450	35
550	35
150	35
225	35
85	35
125	35
100	35
550	35
100	35
550	35
100	35
550	35
100	35
550	35
450	35
550	35
Bake %	35
Tips	35
Auto Convection Conversion	35
Convection Bake 2	36
Tips	36
Convection Multi-Rack:	36
Tips	36
Pizza 2	36
Tips	36
Roast %	37
Tips	37
Convection Roast 2	37
Tips	37
Broil (	37
Tips	37
Convection Broil 4	38
Tips	38
Proof $	38
Warm %	38
9 CAUTION	38
When using Warm mode, follow these guidelines:	38
Cleaning and Maintenance-Oven	39
Cleaning the Oven	39
Self-Clean	39
9 WARNING	39
When using the Self-Clean setting	39
9 CAUTION	39
Avoid risk of damage	39
Self Clean	39
1. Remove all accessories and racks from the oven.	39
2. If there is a cooking mode on, press Oven Clear/Off to end the running mode.	39
3. Press the Self Clean button below the display.	39
4. When the desired Self Clean time is displayed, press Enter on the numeric keypad.	39
Note:	39
5. Self Clean starts and the oven Self Clean timer begins its countdown.	40
6. When the cool down is complete, the message “SELF CLEAN FINISHED” is displayed. Continue to use caution when opening the oven door.	40
7. Press Oven Clear/Off to clear the display when Self Clean is finished.	40
8. After the oven has cooled down and the door is unlocked, wipe remaining ash from the oven using a moist cloth.	40
Notes	40
Avoid These Cleaners	40
Oven Cleaning Guide	40
Maintenance	41
Replacing an Oven Light	41
9 CAUTION	41
when replacing an oven light:	41
Bulb Description	41
Bulb Image	41
How to Remove the Oven Door	42
9 WARNING	42
1. Open the oven door to its fully open position.	42
2. Flip levers on hinges toward you.	42
Note:	42
3. Bring both door hinge levers to their fullest down position as shown in the illustration. The left and right door hinges differ slightly but operate in the same manner.	42
4. Close the oven door until it catches on the hinge stop levers, locking the hinges at the proper angle for door removal. The door will be open about 7 inches at the top. This takes the spring tension off the hinges so the door can be easily lifted out	42
5. The door is heavy. Use both hands to firmly grip it by the sides. Do not grip the door by the handle. Maintaining the door angle, lift the door straight up approximately 3/4” to unhook the hinges from the slots and then pull it out towards you u...	42
6. Place the door in a convenient and stable location for cleaning.	42
How to Replace the Oven Door	43
1. Holding the door firmly in both hands, grip it on either side, not by the handle.	43
2. Tilt the door back slightly towards you until it opens about 7 inches at the top.	43
3. Slide the hinges into the slots as far as they will go and then lower the door straight down. The angle of the door may need to be adjusted slightly to allow the hinges to engage properly and the door to lower into place. The door should lower abo...	43
4. Once both hinges are fully engaged as described in Step 3, gently open the door until it is fully open.	43
5. Push the levers on both the hinges up and forward until they are locked into the slot and flush with the front of the oven body.	43
6. Close and open the door slowly to be sure it is correctly and securely in place.	43
Operation-Warming Drawer	44
About the Warming Drawer	44
Warming Drawer Specifications	44
Operation	44
9 CAUTION	44
Preheating	44
Turning the Warming Drawer On and Off	44
1. Press the Warming Drawer button.	44
2. WARMING DRAWER will be displayed with the default setting “MED”. The warming drawer amber icon is displayed below the clock.	44
3. To accept the “MED” setting, press the Enter button. The setting is accepted and the warming drawer icon remains illuminated. If enter is not pressed, the warming drawer setting is not accepted and the warming drawer turns off.	44
4. To change the setting, when “MED” is displayed, press the Warming Drawer button again. The setting changes to “HIGH”. Press the Warming Drawer button again to change the setting to “LOW”.	44
5. To turn the warming drawer off, press the Warming Drawer button and the warming drawer will turn off. The warming drawer icon will no longer appear under the clock.	44
Sabbath Mode	44
Warming Empty Serving Bowls and Plates	44
Getting the Most Out of Your Warming Drawer	45
About the Appliance	45
General Tips	45
Use of Your Appliance	45
9 CAUTION	45
Note:	45
Preheating	45
Warming Empty Serving Bowls and Plates	45
Crisping Stale Items	45
1. Press LOW.	45
2. Preheat for 10 minutes, then place dish in drawer.	45
3. Set the warming timer.	45
4. Check crispness after 45 minutes. Add time as needed.	45
Temperature Recommendations	46
Food/Cookware	46
Setting	46
Cover Dish	46
HIGH	46
No	46
MED	46
No	46
LOW	46
No	46
MED	46
No	46
MED	46
Yes	46
MED	46
Yes	46
MED	46
Yes	46
MED	46
Yes	46
MED	46
Yes	46
HIGH	46
No	46
MED	46
Yes	46
MED	46
Yes	46
HIGH	46
Yes	46
MED	46
Yes	46
MED	46
No	46
HIGH	46
No	46
MED	46
Yes	46
HIGH	46
Yes	46
MED	46
Yes	46
MED	46
Yes	46
MED	46
Yes	46
LOW	46
No	46
MED	46
Yes	46
Cleaning and Maintenance-Warming Drawer	46
9 CAUTION	46
Note:	46
Cleaning the Warming Drawer	46
Part	46
Recommendations	46
Removing Drawer from Housing	47
NOTICE:	47
1. Remove the drawer from the drawer housing.	47
2. Grasp both sides of the drawer and pulling straight and level, carefully remove the drawer housing. This step may require light to moderate force to completely remove drawer.	47
3. Install or service (clean) housing with drawer removed.	47
Installing Drawer to Housing	47
Note:	47
1. With the drawer removed, set the slide inner rail to the drawer locked position by pushing the slide inner rail toward the rear of the housing until it locks in place.	48
Note:	48
2. Position the drawer assembly in front of the housing assembly and align the rail (plastic rail tip) to the slide ball carrier assembly. Keeping the drawer assembly level and square to the housing, gently insert the drawer to the housing assembly.	48
Notes	48
3. Continue to insert the drawer keeping the drawer level and square to the housing until a slight increase in resistance is felt at the approximate position shown below.	48
NOTICES	49
4. Test the operation of the PTO drawer by pushing on the center lower portion of the drawer front (optimum location for function).	49
Note:	49
Service	50
Frequently-asked questions and answers (FAQ)	50
Fixing Malfunctions	51
9 CAUTION	51
Notes	52
Suitability test of cookware	52
1. With the cookware still cold, fill it with approx. 8 oz. (200 ml) of water and place it on the center of the cooking zone with the diameter that most closely matches that of the base of the cookware.	52

Match case Limit results 1 per page

Fixing Malfunctions

Malfunctions are usually due to small details. Before calling the Customer Support, you should consider the following

advice and warnings.

CAUTION

Repairs should only be done by an authorized

servicer.

Improper repair of your appliance may result in risk

of severe physical injury or death.

Why is it taking so long for the cookware to heat up or why is it not heating up sufficiently despite being on a high

heat setting?

The cookware is too small for the element that is turned on or it is not suitable for induction cooking.

Check that the cookware is suitable for induction cooking and that it is placed on the element that best

corresponds to its size. You can find information on the type, size and positioning of cookware in the

sections on

"Cooking with Induction"

Cookware

Cleaning

How do I clean the cooktop?

Using a special glass-ceramic cleaning agent produces the best results. We advise against using harsh or

abrasive cleaning agents, dishwater detergent (concentrated) or scouring pads.

You can find more information about cleaning and caring for your cooktop in the section on

“Cleaning and Maintenance-Cooktop.”

Display

Possible cause

Solution

None

The power supply has been discon-

nected.

Use other electrical devices to check whether a

short-circuit has occurred in the power supply.

The device has not been connected in

accordance with the connection dia-

gram.

Ensure that the device has been connected in

accordance with the connection diagram.

Electronics error.

If the error cannot be eliminated, inform the

technical after-sales service.

The displays flash

The control panel is damp or an

object is covering it.

Dry the control panel or remove the object.

The

indicator flashes

in the element displays

An error has occurred in the electron-

ics.

To confirm the error, cover the control panel with

your hand.

”ƒ

The electronics have overheated and

have switched off the corresponding

element.

Wait until the electronics have cooled down

sufficiently. Then touch any symbol on the cooktop.

”…

The electronics have overheated and

have switched off all elements.

”†

+ heat setting and

acoustic signal

There is a hot pan in the area of the

control panel. There is a risk that the

electronics will overheat.

Remove the pan. The error display goes out shortly

afterwards. You can continue to cook.

”†

and acoustic signal

There is a hot pan in the area of the

control panel. To protect the electron-

ics, the element has been switched

off.

Remove the pan. Wait for a few seconds. Touch

any control. If the error display goes out, you can

continue to cook.

”‚

”‡

The element has overheated and

switched itself off to protect the work

surface.

Wait until the electronics have cooled down

sufficiently and switch the element on again.

”‰

The element was operating for an

extended period without interruption.

The automatic safety switch-off function has been

activated. See section “Automatic time limitation”

Do not place hot pans on the control panel.