Bosch NITP068UC Instructions for Use - Page 22
Fixing Malfunctions
View all Bosch NITP068UC manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 22 highlights
Cookware Why is it taking so long for the cookware to heat up or why is it not heating up sufficiently despite being on a high heat setting? The cookware is too small for the element that is turned on or it is not suitable for induction cooking. Check that the cookware is suitable for induction cooking and that it is placed on the element that best corresponds to its size. You can find information on the type, size and positioning of cookware in the sections on ~ "Cooking with Induction", ~ "FlexInduction® cooking zone" and ~ "PowerMove function" Cleaning How do I clean the cooktop? Using a special glass-ceramic cleaning agent produces the best results. We advise against using harsh or abrasive cleaning agents, dishwater detergent (concentrated) or scouring pads. You can find more information about cleaning and caring for your cooktop in the section on Fixing Malfunctions Malfunctions are usually due to small details. Before calling the Technical Assistance Service, you should consider the following advice and warnings. 9 CAUTION Repairs should only be done by an authorized servicer. Improper repair of your appliance may result in risk of severe physical injury or death. Display Possible cause Solution None The power supply has been discon- Use other electrical devices to check whether a nected. short-circuit has occurred in the power supply. The device has not been connected in Ensure that the device has been connected in accordance with the connection dia- accordance with the connection diagram. gram. Electronics error. If the error cannot be eliminated, inform the technical after-sales service. The displays flash The Ù indicator flashes in the element displays "ƒ "... "† + heat setting and acoustic signal "† and acoustic signal ",/"‡ The control panel is damp or an object is covering it. An error has occurred in the electronics. The electronics have overheated and have switched off the corresponding element. The electronics have overheated and have switched off all elements. There is a hot pan in the area of the control panel. There is a risk that the electronics will overheat. There is a hot pan in the area of the control panel. To protect the electronics, the element has been switched off. The element has overheated and switched itself off to protect the work surface. The element was operating for an extended period without interruption. The supply voltage is incorrect; outside of the normal operating range. Dry the control panel or remove the object. To confirm the error, cover the control panel with your hand. Wait until the electronics have cooled down sufficiently. Then touch any symbol on the cooktop. Remove the pan. The error display goes out shortly afterwards. You can continue to cook. Remove the pan. Wait for a few seconds. Touch any control. If the error display goes out, you can continue to cook. Wait until the electronics have cooled down sufficiently and switch the element on again. The automatic safety switch-off function has been activated. See section "Automatic time limitation" Contact your electrical utility provider. Do not place hot pans on the control panel. 22
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76