Bosch SHE89PW55N Instructions for Use - Page 34
Operating the, Dishwasher
View all Bosch SHE89PW55N manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 34 highlights
en-us Operating the Dishwasher 1 Operating the Dishwasher Note: rehsawhsiDehtgnitarepO With hidden controls, the door must be opened before changing settings and closed after changing settings. 9 WARNING RISK OF INJURY! To avoid risk of injury, always use caution when opening the door during or following a wash cycle as hot water or steam may escape. Do not fully open the door until water noises have stopped and steam has subsided. Protection against unintentional operation Your dishwasher is equipped with a function that helps to prevent unintentional operation (e.g. by children). After setting the dishwasher, the dishwasher door has to be closed within 4 seconds, otherwise the operation will be paused. There will be a signal on the control panel advising you to press the Start button again and close the door. This function will be activated when: ■ pressing Start to begin a wash cycle ■ setting Delay time and pressing Start ■ opening the door while Delay time is active ■ opening the door during a wash cycle. Note: This function cannot be deactivated. Operating the touch buttons Buttons are sensitive and should be touched gently. Avoid any grease or food particles resting on the buttons as they could activate the dishwasher. Wiping and cleaning can also activate the dishwasher. For best results, use bare, clean hands when touching the buttons. To clean the touch buttons wipe them with a dry or slightly damp cloth. Changing the settings The dishwasher has been preset with certain settings for your convenience. You can change these factory settings. Change the setting as follows: 1. Open the door. 2. Switch on On/Off button (. 3. Press Info button 8 for 3 seconds until the following text is indicated in the digital display @: Scroll with < > Set with - + Leave with Setup 3 sec. 4. Keep pressing button > )* until the required setting is indicated in the display window at the top @. 5. Make the selection with setting buttons + -X. 6. Press and hold the Info button 8 for 3 seconds. The chosen setting has now been stored. Tip: If you change several settings, first make all changes in succession. Now press the Info button 8 for 3 seconds. This saves all set values in the appliance. 34
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108