Bosch SHX3AR72UC Instructions for Use - Page 15

Operating the Dishwasher

Page 15 highlights

Operating the Dishwasher Start the dishwasher: 1 Open the door and press the On/Off button. 2 One of the wash cycle LEDs will be flashing. You can now select a wash cycle. 3 Press the Cycle Select arrow buttons to select the desired wash cycle. 4 Press Start and close the door to begin the cycle. Cancel a cycle: 1 Open the dishwasher door just far enough to expose the control panel. Be careful of hot water that may splash out. 2 Press and hold Start until the "Active" LED goes out. 3 Close the door and wait about 1 minute until the unit beeps, indicating it is done draining. 4 Open the door and press the On/Off button. You may now start a new cycle. WARNING You could be seriously scalded if you allow hot water to splash out of the dishwasher. OPEN THE DOOR CAREFULLY during any wash or rinse cycle. Do not fully open the door until water noises have stopped. To enter options mode: 1 With the door open, press the On/Off button to turn the unit on. 2 One of the wash cycle LEDs will be flashing. 3 Press and hold down the > button, then press and release the Start button. Now release the > button. 4 The "Clean" LED and one other LED will be flashing. You are now in options mode. 5 Press the > button to select the option you would like to adjust. To set amount of Rinse Aid: Note: If your glasses have spots on them, you need more rinse aid. If your glasses have streaks on them, you need less rinse aid. 1 Follow the prior instructions to enter options mode. 2 With the "Clean" and "Refill Rinse Aid" LEDs flashing, press the < button to change the amount of rinse aid dispensed. 0 LEDs flashing = rinse aid is OFF 1 LED flashing = lowest amount of rinse aid dispensed 2 LEDs flashing = medium amount of rinse aid dispensed 3 LEDs flashing = highest amount of rinse aid dispensed 3 Press Start to save your setting. To turn Extra Dry Heat ON or OFF: 1 Follow the prior instructions to enter options mode. 2 With the "Clean" and "Sanitized" LEDs flashing, press the < button to turn Extra Dry Heat ON or OFF. 0 LEDs flashing = Extra Dry Heat is OFF 1 LED flashing = Extra Dry Heat is ON 3 Press Start to save your setting. To set the Cycle Completion Signal: 1 With the "Clean", "Sanitized" and "Refill Rinse Aid" LEDs flashing, press the < button to change the cycle completion tone volume. The wash cycle LEDs will illuminate when you press

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64

13
Operating the Dishwasher
Start the dishwasher:
1
Open the door and press the
On/Off
button.
2
One of the wash cycle LEDs will be flashing. You can now select a wash cycle.
3
Press the
Cycle Select
arrow buttons to select the desired wash cycle.
4
Press
Start
and close the door to begin the cycle.
Cancel a cycle:
1
Open the dishwasher door just far enough to expose the control panel. Be careful of hot water that
may splash out.
2
Press and hold
Start
until the “Active” LED goes out.
3
Close the door and wait about 1 minute until the unit beeps, indicating it is done draining.
4
Open the door and press the
On/Off
button. You may now start a new cycle.
WARNING
You could be seriously scalded if you allow hot water to splash out of the dishwasher. OPEN THE DOOR
CAREFULLY during any wash or rinse cycle. Do not fully open the door until water noises have stopped.
To enter options mode:
1
With the door open, press the
On/Off
button to turn the unit on.
2
One of the wash cycle LEDs will be flashing.
3
Press and hold down the
>
button, then press and release the
Start
button. Now release the
>
button.
4
The “Clean” LED and one other LED will be flashing. You are now in options mode.
5
Press the
>
button to select the option you would like to adjust.
To set amount of Rinse Aid:
Note: If your glasses have spots on them, you need more rinse aid. If your glasses have streaks on them, you
need less rinse aid.
1
Follow the prior instructions to enter options mode.
2
With the “Clean” and “Refill Rinse Aid” LEDs flashing, press the
<
button to change the amount of
rinse aid dispensed.
0 LEDs flashing
= rinse aid is OFF
1 LED flashing
= lowest amount of rinse aid dispensed
2 LEDs flashing
= medium amount of rinse aid dispensed
3 LEDs flashing
= highest amount of rinse aid dispensed
3
Press
Start
to save your setting.
To turn Extra Dry Heat ON or OFF:
1
Follow the prior instructions to enter options mode.
2
With the “Clean” and “Sanitized” LEDs flashing, press the
<
button to turn Extra Dry Heat ON or OFF.
0 LEDs flashing
= Extra Dry Heat is OFF
1 LED flashing
= Extra Dry Heat is ON
3
Press
Start
to save your setting.
To set the Cycle Completion Signal:
1
With the “Clean”, “Sanitized” and “Refill Rinse Aid” LEDs flashing, press the
<
button to change the
cycle completion tone volume. The wash cycle LEDs will illuminate when you press
<
.
0 LEDs flashing
= Cycle Completion Signal is OFF
1 LED flashing
= low tone volume
2 LEDs flashing
= medium tone volume
3 LEDs flashing
= highest tone volume
2
Press
Start
to save your setting.