Bosch WTMC533SUS Operating, Care, Installation - Page 7
Notice, Warning - tools
![]() |
View all Bosch WTMC533SUS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
Useful Tools The following tools are helpful during installation: 1. T20 star head screwdriver 2. Philips screwdriver (#2) 3. Flat blade screwdriver 4. Open end wrench 1 in. (25mm) 5. Bubble level Checklist for Installation 1. Unpack the dryer. 2. Remove all objects from the drum. 3. Check the dryer for visible damage. 4. Position the dryer near the installation location (see page 7). 5. If required, change the door hinge to the left (see page 15). 6. If required, install the side or bottom exhaust air outlet on the dryer (see page 15). 7. Have the power supply cord fitted by a qualified technician or a licensed electrician (see page 9). 8. Check for Y" connection, short hose and AQUASTOP® Hose included with the dryer packaging (see page 8). 9. Connect the water supply to the back of the dryer (see page 8 for detailed instructions). 10. Install exhaust ductwork if necessary. Follow the installation instructions supplied by the appropriate ductwork parts manufacturers (see page 14) i If space is very restricted, it is recommended to fit the initial parts of the exhaust duct to the dryer before the dryer is moved to its final installation location. 11. Move the dryer to its final location. NOTICE Do not slide dryer across the floor if heightĆadjustable feet have been extended. Feet and/or dryer base may be damaged if dryer is slid across floor with heightĆadjustable feet extended. 12. Position and then level the dryer. The dryer should be level with all four feet firmly on the ground. The dryer must not wobble. If the dryer is not level or if it does wobble, the feet must be adjusted. Adjust the heightĆadjustable feet until the dryer does not rock and is level, both frontĆtoĆback and sideĆtoĆside. q After making preliminary adjustments, press down on each corner of the dryer to make sure the unit does not wobble. If it does wobble, lower the foot on that corner until the foot touches the floor firmly. Install the dryer and level side to side and front to back. Use a bubble level. Never remove the heightĆadjustable feet! 13. Connect the exhaust duct to the exhaust air outlet on the dryer (see page 13). 14. Insert the dryer electrical plug into the wall receptacle (see page 9). 15. Read the operating instructions to understand how your dryer operates. (see page 16). 16. Conduct an appliance test: q Check that the drum is empty. q Close the dryer door. q Switch the dryer to "Extra Dry" and then press the Start" button. q After 3-5 minutes press the Stop button and open the door. q If the interior of the dryer feels warm, the dryer has been connected properly. Switch the dryer to "OFF". q If the dryer does not work, switch the dryer to "OFF". Look in the troubleshooting section (page 25) and find the fault. Installation location d WARNING DO NOT install the dryer: - outdoors - in an environment with dripping water, - near flammable materials, - in rooms which are at risk of frost, - in rooms which may contain gas or other fuels, - in cupboards with lockable doors or in alcoves. The installation room must be well ventilated, otherwise the dryer will operate below optimum performance. Do not operate the dryer at temperatures above 104°F (40°C) or below 41°F (5°C). Low temperatures affect the automatic program sequence and may prolong the drying times. The installation surface for the dryer must be clean, level and firm. Do not install the appliance on carpets! Compensate for uneven floors with the heightĆadjustable feet. 7
![](/manual_guide/products/bosch-wtmc5330us-operating-care-installation-6101486/7.png)