Bosch WTVC8530UC Operating Guide - Page 29

Cleaning, and care - power tools

Get Bosch WTVC8530UC - Vision 800 Series Gas Dryer PDF manuals and user guides
UPC - 825225874447
View all Bosch WTVC8530UC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Cleaning and care Cleaning the dryer TO AVOID RISK OF EXPLOSION! Never use solvents or highly flammable liquids for cleaning. Incorrect cleaning may damage the dryer. Do not spray with a pressure washer. Do not use scouring agents or all-purpose cleaners. Do not use steam cleaners. Wipe the housing and the control panel with a soft cloth and soapy water only. Wipe the drum, door seal and inside of the door with a damp cloth only. Cleaning the exhaust duct Inspect and clean the exhaust ducting at least once a year to prevent clogging. A partially clogged exhaust will lengthen the drying time and will result in poor performance of the dryer. Turn off the circuit breaker Unplug the dryer from the power supply. Disconnect the duct from the dryer. Vacuum the inside of the duct to remove any accumulation of lint or debris. Reconnect the duct. Professional duct cleaning is recommended. See page 17. Cleaning the moisture sensor The moisture sensor has to be cleaned periodically because a fine layer of transparent buildup is deposited on the sensors. This deposit can easily be removed by wiping the sensors (the two bars next to the lint filter) with a cloth and a little white vinegar. Use white vinegar only! Clean the moisture sensor once a month. Cleaning the lint filter housing Lint and small debris may accumulate in the lower portion of the lint filter opening. With the lint filter removed, accumulated lint can be seen and easily removed with a vaccum cleaner using a narrow crevice cleaning tool. If you do not have a crevice cleaning tool that will reach to the bottom of the opening, you may contact Customer Service for a list of sources and recommended attachments. Any accumulation of lint or debris should be removed at least once a month using your vacuum cleaner. Cleaning the Steam nozzle Once a year, inspect the nozzle outlet. If you suspect blockage, wipe the outside of the nozzle with a cloth moistened with vinegar. If the nozzle is completely blocked, consult the troubleshooting guide (see page 31) for removal and cleaning instructions. If the nozzle remains blocked, call customer service (see page 32). Change the light bulb The dryer light turns on inside the drum when you open the door and stays on for for about 5 minutes or until the door is closed. The light turns off about 4 seconds after the door is closed. To change the light bulb: Set program selector to "Off". Turn off the circuit breaker. Unplug the dryer from the power supply. Open the door and locate the dryer light on the upper left side of the seal. Loosen the screw and open the dryer light cover. Turn bulb counterclockwise. Replace the bulb with a new appliance bulb only (obtainable through parts department). % Parts are available at www.boschappliances.com or by calling 1 800 944-2904. Replace the cover and secure with the screw. Plug the dryer back into the power supply. Turn on the circuit breaker. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Cleaning
and care
Cleaning
the dryer
TO AVOID
RISK
OF
EXPLOSION!
Never
use solvents
or highly
flammable
liquids
for cleaning.
Incorrect cleaning may damage the
dryer. Do not spray with a pressure
washer. Do not use scouring agents
or all-purpose cleaners. Do not use
steam cleaners.
Wipe the housing and the control panel
with a soft cloth and soapy water only.
Wipe the drum, door seal and inside of
the door with a damp cloth only.
Cleaning
the exhaust
duct
Inspect and clean the exhaust ducting
at least once a year to prevent
clogging. A partially clogged exhaust
will lengthen the drying time and will
result in poor performance of the dryer.
Turn off the circuit breaker
Unplug the dryer from the power
supply.
Disconnect the duct from the
dryer.
Vacuum the inside of the duct to
remove any accumulation
of lint or
debris.
Reconnect the duct.
Professional duct cleaning is
recommended.
See page 17.
Cleaning
the moisture
sensor
The moisture sensor has to be cleaned
periodically because a fine layer of
transparent buildup is deposited on the
sensors.
This deposit can easily be removed by
wiping the sensors (the two bars next
to the lint filter) with a cloth and a little
white vinegar.
Use white
vinegar
only!
Clean the moisture sensor once a
month.
Cleaning
the lint filter
housing
Lint and small debris may accumulate
in the lower portion of the lint filter
opening.
With the lint filter removed,
accumulated
lint can be seen and
easily removed with a vaccum cleaner
using a narrow crevice cleaning tool.
If you do not have a crevice cleaning
tool that will reach to the bottom of the
opening, you may contact Customer
Service for a list of sources and
recommended
attachments.
Any accumulation
of lint or debris
should be removed at least once a
month using your vacuum cleaner.
Cleaning
the Steam
nozzle
Once a year, inspect the nozzle outlet.
If you suspect blockage, wipe the
outside of the nozzle with a cloth
moistened with vinegar.
Ifthe nozzle is
completely blocked, consult the
troubleshooting
guide (see page 31) for
removal and cleaning instructions.
If
the nozzle remains blocked, call
customer service (see page 32).
Change
the light
bulb
The dryer light turns on inside the drum
when you open the door and stays on
for for about 5 minutes or until the door
is closed.
The light turns off about 4
seconds after the door is closed.
To change the light bulb:
Set program selector to "Off".
Turn off the circuit breaker.
Unplug the dryer from the power
supply.
Open the door and locate the
dryer light on the upper left side of
the seal.
%
Loosen the screw and open the
dryer light cover.
Turn bulb counterclockwise.
Replace the bulb with a new
appliance bulb only (obtainable
through parts department).
Parts are available at
www.boschappliances.com
or by calling 1 800
944-2904.
Replace the cover and secure with
the screw.
Plug the dryer back into the power
supply.
Turn on the circuit breaker.
29