Bose VS-100 Owner's guide - Page 6

Bose VS-100 Manual

Get Bose VS-100 PDF manuals and user guides View all Bose VS-100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

First strip about 1/2 inch (12 mm) of insulation from each wire and twist the separate wire ends. Then, to connect a wire, push the terminal tab dawn. Insert the end of the wire into the exposed hole. Release the tab to secure the wire (Figure 3). To connect a center channel speaker Attach both wires at one end of the cord to the terminals on the back of the speaker. Make sure the connections are made positive to positive and negative to negative. Now connect the free end of the cord to the CENTER (C) SPEAKER terminals on your receiver. If there is more than one center channel set of terminals(+and-),use either set. Ceder Channel Speaker To connect a rear channel speaker Attach both wires at one end of a cord to the terminals on the back of one speaker. Make sure the connections are made positive to positive and negative to negative. Now connect the free end of that cord to the REAR SPEAKERS(L)or (R) terminals on your receiver. Tip: II does not matter which of these speakers is connected to the L and which to theR terminals. Therefore you don't need to cross the wires leading from your speakers to your receiver. Check your connections before • turning the system on Make sure ' inflections are tight and have been made positive to positive andnegative to negative (marked wire to red, plain wire to black). Check to be sure that wires do not touch across terminals, which can damage your speakers. Correct any problems before you plug thereceiver in and turnit on •a ACI) To Right Speaker To Left Speaker Amplilierireceiver outputs Figure 3 •

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
First
strip
about
1/2
inch
(12
mm)
of
insulation
from
each
wire
and
twist
the
separate
wire
ends.
Then,
to
connect
a
wire,
push
the
terminal
tab
dawn.
Insert
the
end
of
the
wire
into
the
exposed
hole.
Release
the
tab
to
secure
the
wire
(Figure
3).
To
connect
a
center
channel
speaker
Attach
both
wires
at
one
end
of
the
cord
to
the
terminals
on
the
back
of
the
speaker.
Make
sure
the
connections
are
made
positive
to
positive
and
negative
to
negative.
Now
connect
the
free
end
of
the
cord
to
the
CENTER
(C)
SPEAKER
terminals
on
your
receiver.
If
there
is
more
than
one
center
channel
set
of
terminals
(+
and
-),
use
either
set.
Ceder
Channel
Speaker
To
Right
Speaker
To
Left
Speaker
Amplilierireceiver
outputs
Figure
3
To
connect
a
rear
channel
speaker
Attach
both
wires
at
one
end
of
a
cord
to
the
terminals
on
the
back
of
one
speaker.
Make
sure
the
connections
are
made
positive
to
positive
and
negative
to
negative.
Now
connect
the
free
end
of
that
cord
to
the
REAR
SPEAKERS
(L)
or
(R)
terminals
on
your
receiver.
Tip:
II
does
not
matter
which
of
these
speakers
is
connected
to
the
L
and
which
to
the
R
terminals.
Therefore
you
don't
need
to
cross
the
wires
leading
from
your
speakers
to
your
receiver.
Check
your
connections
before
turning
the
system
on
Make
sure
'
inflections
are
tight
and
have
been
made
positive
to
positive
and
negative
to
negative
(marked
wire
to
red,
plain
wire
to
black).
Check
to
be
sure
that
wires
do
not
touch
across
terminals,
which
can
damage
your
speakers.
Correct
any
problems
before
you
plug
the
receiver
in
and
turn
it
on
•a
ACI)
•
•