Brother International HL 1040 Users Manual - English - Page 56

Serial Interface Parity, Use Printer TrueType

Get Brother International HL 1040 - Printer - B/W PDF manuals and user guides
UPC - 012502525219
View all Brother International HL 1040 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

USER'S GUIDE For errors shown below, the printer indicates an operator call by blinking the Alarm lamp. If you use the printer with the supplied Windows driver, the status monitor will appear to indicate the error on your computer screen. The HL-1040/1050 printer also prints some error messages on paper. Error Action COVER OPEN Close the top cover of the printer. PRINT OVERRUN Press the panel switch to print the data remaining in the printer. If you use the supplied Windows driver, try again after turning on Error Recovery in the PRINT menu of your application software, (Refer to Help section in Windows printer driver for the details.) For HL-1050 only Expand the printer memory with an optional memory board and set page protection to ON by using the suuplied Windows driver or RPC program. For HL-1050 only Change the following settings in the supplied Windows driver and try again. The best combination of the settngs below will vary depending on your document. Graphics Mode TrueType mode Use Printer TrueType Fonts If this does not clear the error, reduce the complexity of your document or reduce the print resolution. MEMORY FULL (For HL-1040/1050 Only) This error can occur only when using DOS or Macintosh. Press the panel switch to print the data remaining in the printer. Reduce the print resolution or reduce the complexity of your document. For HL-1050 only Expand the printer memory.by adding a commercially available SIMM. Parallel Interface Line Error Press the panel switch to resume printing. Check that the connection between your computer and printer is secure and correct, and check the interface cable. Serial Interface Framing Error (For HL-1040/1050 Only) Press the panel switch to resume printing. Check the communication parameters such as baud rate and stop bit settingson both your computer and printer. Serial Interface Parity Error (For HL-1040/1050 Only) Press the panel switch to resume printing. Check the communication parameters such as bit length and parity settings on both your computer and printer. 6-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
USER’S GUIDE
6-2
For errors shown below, the printer indicates an operator call by blinking
the
Alarm
lamp. If you use the printer with the supplied Windows driver,
the status monitor will appear to indicate the error on your computer
screen. The HL-1040/1050 printer also prints some error messages on
paper.
Error
Action
COVER OPEN
Close the top cover of the printer.
PRINT OVERRUN
Press the panel
switch
to print the data remaining in the
printer.
If you use the supplied Windows driver, try again after
turning on Error Recovery in the PRINT menu of your
application software, (Refer to Help section in Windows
printer driver for the details.)
For HL-1050 only
Expand the printer memory with an optional memory
board and set page protection to ON by using the suuplied
Windows driver or RPC program.
For HL-1050 only
Change the following settings in the supplied Windows
driver and try again.
The best combination of the settngs
below will vary depending on your document.
Graphics Mode
TrueType
mode
Use Printer TrueType
Fonts
If this does not clear the error, reduce the complexity of
your document or reduce the print resolution.
MEMORY FULL
(For HL-1040/1050 Only)
This error can occur only
when using DOS or
Macintosh.
Press the panel
switch
to print the data remaining in the
printer.
Reduce the print resolution or reduce the complexity of
your document.
For HL-1050 only
Expand the printer memory.by adding a commercially
available SIMM.
Parallel Interface Line
Error
Press the panel
switch
to resume printing.
Check that the connection between your computer and
printer is secure and correct, and check the interface cable.
Serial Interface Framing
Error
(For HL-1040/1050 Only)
Press the panel
switch
to resume printing.
Check the communication parameters such as baud rate
and stop bit settingson both your computer and printer.
Serial Interface Parity
Error
(For HL-1040/1050 Only)
Press the panel
switch
to resume printing.
Check the communication parameters such as bit length
and parity settings on both your computer and printer.