Brother International LX-3125 Users Manual - English and Spanish - Page 12

Lower threading - needle

Get Brother International LX-3125 PDF manuals and user guides View all Brother International LX-3125 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

KNOWING YOUR SEWING MACHINE Trim the excess thread above the bobbin. g Lower threading Install the bobbin wound with thread. CAUTION ● Make sure you follow the instructions carefully. If you do not cut the thread completely, and the bobbin is wound, when the thread runs low it may tangle around the bobbin and cause the needle to break. CAUTION ● Winding the bobbin improperly may cause the thread tension to loosen, breaking the needle and resulting in injury. Press the foot controller to start. h When the bobbin seems full and begins spinning i slowly, take your foot off the foot controller. Cut the thread, slide the bobbin winder shaft j to the left and remove the bobbin. Memo ● When the sewing machine is started or the handwheel is turned after winding the thread around the bobbin, the machine will make a clicking sound; this is not a malfunction. ● The needle bar does not move when you slide the bobbin winding shaft to the right. CAUTION ● Winding the bobbin improperly may cause the thread tension to loosen, breaking the needle and resulting in injury. 1 2 a Wound evenly b Wound poorly ● The bobbin was designed specifically for this sewing machine. If bobbins from other models are used, the machine will not operate correctly. Use only the enclosed bobbin or bobbins of the same type (part code: SA156, SFB: XA5539-151). Actual size 11.5 mm (7/16 inches) This model Other models CAUTION ● Make sure you turn the power off while threading the machine. If you accidentally step on the foot controller and the machine starts to sew, you could be injured. Raise the needle to its highest position by turning a the handwheel toward you (counterclockwise) and raise the presser foot lever. 1 2 a Wound evenly b Wound poorly 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
KNOWING YOUR SEWING MACHINE
—————————————————————————————————————————
11
g
Trim the excess thread above the bobbin.
h
Press the foot controller to start.
i
When the bobbin seems full and begins spinning
slowly, take your foot off the foot controller.
j
Cut the thread, slide the bobbin winder shaft
to the left and remove the bobbin.
Memo
●
When the sewing machine is started or the
handwheel is turned after winding the
thread around the bobbin, the machine will
make a clicking sound; this is not a
malfunction.
●
The needle bar does not move when you
slide the bobbin winding shaft to the right.
Lower threading
Install the bobbin wound with thread.
a
Raise the needle to its highest position by turning
the handwheel toward you (counterclockwise)
and raise the presser foot lever.
●
Make sure you follow the instructions
carefully. If you do not cut the thread
completely, and the bobbin is wound, when
the thread runs low it may tangle around the
bobbin and cause the needle to break.
●
Winding the bobbin improperly may cause
the thread tension to loosen, breaking the
needle and resulting in injury.
a
Wound evenly
b
Wound poorly
CAUTION
CAUTION
1
2
●
Winding the bobbin improperly may cause
the thread tension to loosen, breaking the
needle and resulting in injury.
a
Wound evenly
b
Wound poorly
●
The bobbin was designed specifically for this
sewing machine. If bobbins from other
models are used, the machine will not operate
correctly. Use only the enclosed bobbin or
bobbins of the same type (part code: SA156,
SFB: XA5539-151).
●
Make sure you turn the power off while
threading the machine. If you accidentally
step on the foot controller and the machine
starts to sew, you could be injured.
CAUTION
1
2
Actual size
This model
Other models
11.5 mm
(7/16 inches)
CAUTION