Brother International NX-600 Users Manual - English - Page 148

Troubleshooting, Symptom, Probable Cause, Remedy, Reference

Get Brother International NX-600 PDF manuals and user guides View all Brother International NX-600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 148 highlights

APPENDIX CONTENTS GETTING READY SEWING BASICS UTILITY STITCHES Troubleshooting If the machine stops operating correctly, check the following possible problems before requesting service. If the problem persists, contact your retailer or the nearest authorized service center. Symptom Probable Cause Remedy The machine is not turned on. Turn on the machine. The sewing machine does not operate. The start/stop button was not pressed. The presser foot lever is raised. The start/stop button was pressed, even though the foot controller is connected. Press the start/stop button. Lower the presser foot lever. Do not use the start/stop button when the foot controller is connected. To use the start/stop button, disconnect the foot controller. The needle is incorrectly installed. Correctly install the needle. The needle clamp screw is loose. Use the screwdriver to firmly tighten the screw. The needle is bent or blunt. Replace the needle. The combination of fabric, thread and needle is not correct. Select a thread and needle that are appropriate for the type of fabric being sewn. The presser foot that is used is not Attach the presser foot that is appropriate for the type of stitch that appropriate for the type of stitch you wish to sew. that you wish to sew. The upper thread tension is too tight. Loosen the upper thread tension. The fabric is pulled too much. The needle breaks. The spool is incorrectly installed. Lightly guide the fabric. Correctly install the spool. The area around the hole in the needle plate is scratched, or has a burr on it. Replace the needle plate. Contact your retailer or the nearest authorized service center. The area around the hole in the presser foot is scratched, or has a burr on it. Replace the presser foot. Contact your retailer or the nearest authorized service center. The shuttle is scratched, or has a burr on it. Replace the shuttle. Contact your retailer or the nearest authorized service center. A bobbin designed specifically for this machine is not used. Incorrect bobbins will not work properly. Only use a bobbin designed specifically for this machine. Reference page 11 page 48 - page 48 page 35 page 34 page 132 page 53 - page 24 - - - page 18 APPENDIX INDEX 142

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
APPENDIX
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
142
GETTING READY
CONTENTS
SEWING BASICS
UTILITY STITCHES
APPENDIX
INDEX
Troubleshooting
If the machine stops operating correctly, check the following possible problems before requesting service.
If the problem persists, contact your retailer or the nearest authorized service center.
Symptom
Probable Cause
Remedy
Reference
The sewing
machine does not
operate.
The machine is not turned on.
Turn on the machine.
page 11
The start/stop button was not
pressed.
Press the start/stop button.
page 48
The presser foot lever is raised.
Lower the presser foot lever.
–
The start/stop button was pressed,
even though the foot controller is
connected.
Do not use the start/stop button
when the foot controller is
connected. To use the start/stop
button, disconnect the foot
controller.
page 48
The needle breaks.
The needle is incorrectly installed.
Correctly install the needle.
page 35
The needle clamp screw is loose.
Use the screwdriver to firmly
tighten the screw.
The needle is bent or blunt.
Replace the needle.
The combination of fabric, thread
and needle is not correct.
Select a thread and needle that
are appropriate for the type of
fabric being sewn.
page 34
The presser foot that is used is not
appropriate for the type of stitch that
you wish to sew.
Attach the presser foot that is
appropriate for the type of stitch
that you wish to sew.
page 132
The upper thread tension is too tight.
Loosen the upper thread tension.
page 53
The fabric is pulled too much.
Lightly guide the fabric.
–
The spool is incorrectly installed.
Correctly install the spool.
page 24
The area around the hole in the
needle plate is scratched, or has a
burr on it.
Replace the needle plate. Contact
your retailer or the nearest
authorized service center.
–
The area around the hole in the
presser foot is scratched, or has a
burr on it.
Replace the presser foot. Contact
your retailer or the nearest
authorized service center.
–
The shuttle is scratched, or has a burr
on it.
Replace the shuttle. Contact your
retailer or the nearest authorized
service center.
–
A bobbin designed specifically for
this machine is not used.
Incorrect bobbins will not work
properly. Only use a bobbin
designed specifically for this
machine.
page 18