Brother International SE 350 Users Manual - English - Page 13

Needle and presser foot, Right-side/rear view - sew and embroidery machine

Get Brother International SE 350 - Compact Sewing & Embroidery Combo Machine PDF manuals and user guides
UPC - 012502619703
View all Brother International SE 350 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Needle and presser foot section Right-side/rear view a Buttonhole lever (page 86) Lower the buttonhole lever when sewing buttonholes and bar tacks. b Thread guide disk (page 34) Pass the thread through the thread guide disk when using the needle threader to thread the needle. c Needle bar thread guide (page 34) Pass the upper thread through the needle bar thread guide. d Needle plate (page 67) The needle plate is marked with guides for sewing straight seams. e Needle plate cover (page 152) Remove the needle plate cover to clean the bobbin case and race. f Bobbin cover/bobbin case (page 28) Remove the bobbin cover, and then insert the bobbin into the bobbin case. g Feed dogs (page 88) The feed dogs feed the fabric in the sewing direction. h Presser foot (page 43, 50) The presser foot applies pressure consistently on the fabric as the sewing takes place. Attach the appropriate presser foot for the selected stitching. i Presser foot holder (page 45) The presser foot is installed onto the presser foot holder. a Handle Carry the sewing machine by its handle when transporting the machine. b Handwheel (page 50) Turn the handwheel toward you (counterclockwise) to raise and lower the needle to sew one stitch. c Embroidery card slot (page 138) Insert the embroidery card. d Air vent The air vent allows the air surrounding the motor to be exchanged. Do not cover the air vent while the sewing machine is being used. e Main power switch (page 17) Use the main power switch to turn the sewing machine on and off. f Foot controller jack (page 52) Insert the plug on the end of the foot controller cable into the foot controller jack. g Power supply jack (page 17) Insert the plug on the power supply cord into the power supply jack. h Drop feed lever (page 88) Use the drop feed lever to lower the feed dogs. Memo z Refer to pages 10 through 13 while you are learning to use your machine. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
11
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
Needle and presser foot
section
a
Buttonhole lever
(
page 86
)
Lower the buttonhole lever when sewing buttonholes
and bar tacks.
b
Thread guide disk (page 34
)
Pass the thread through the thread guide disk when
using the needle threader to thread the needle.
c
Needle bar thread guide (page 34)
Pass the upper thread through the needle bar thread
guide.
d
Needle plate (page 67)
The needle plate is marked with guides for sewing
straight seams.
e
Needle plate cover (page 152)
Remove the needle plate cover to clean the bobbin case
and race.
f
Bobbin cover/bobbin case (page 28)
Remove the bobbin cover, and then insert the bobbin
into the bobbin case.
g
Feed dogs
(
page 88
)
The feed dogs feed the fabric in the sewing direction.
h
Presser foot (page 43, 50)
The presser foot applies pressure consistently on the
fabric as the sewing takes place. Attach the appropriate
presser foot for the selected stitching.
i
Presser foot holder
(
page 45
)
The presser foot is installed onto the presser foot holder.
Right-side/rear view
a
Handle
Carry the sewing machine by its handle when
transporting the machine.
b
Handwheel (page 50)
Turn the handwheel toward you (counterclockwise) to
raise and lower the needle to sew one stitch.
c
Embroidery card slot (page 138)
Insert the embroidery card.
d
Air vent
The air vent allows the air surrounding the motor to be
exchanged. Do not cover the air vent while the sewing
machine is being used.
e
Main power switch (page 17)
Use the main power switch to turn the sewing machine
on and off.
f
Foot controller jack (page 52)
Insert the plug on the end of the foot controller cable
into the foot controller jack.
g
Power supply jack (page 17)
Insert the plug on the power supply cord into the power
supply jack.
h
Drop feed lever
(
page 88
)
Use the drop feed lever to lower the feed dogs.
Memo
Refer to pages 10 through 13 while you are
learning to use your machine.