Brother International Simplicity SB530T Users Manual - English and Spanish - Page 31

turn the handwheel toward

Get Brother International Simplicity SB530T PDF manuals and user guides View all Brother International Simplicity SB530T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

■ Attaching the extra spool pin Insert the extra spool pin onto the end of the bobbin winder shaft. Install the second thread spool onto the extra spool pin. 1 Bobbin winder shaft 2 Extra spool pin 3 Thread spool Thread the right needle. 3 Thread the right needle in the same way that you threaded the left needle using the thread from the spool on the extra spool pin, but do not pass the thread through the guide above the needle before you pass it through the eye of the right needle. 3 2 2 1 ■ Twin needle threading You should thread each needle separately. Note ● You cannot use the needle threader to thread the twin needle. Instead, thread the twin needle by hand, from front to back. Using the needle threader may damage the machine (see page 24). Thread the upper thread for the right side 1 in the same way that the upper thread for the left side was threaded. 1 1 Thread guide • For details, refer to step 1 through 0 of "Upper threading" (page 20). Thread the left needle. 2 1 Left needle thread passes through the needle bar thread guide 2 Right needle thread passes in front of the needle bar thread guide 3 Needle bar thread guide Attach zigzag foot "J". 4 For details on changing the presser foot, refer to "Changing the presser foot" on page 8. CAUTION ● When using the twin needle, be sure to attach zigzag foot "J", otherwise the needle may break or the machine may be damaged. Turn on the machine. 5 CAUTION ● Do not turn on the machine while pressing down the foot controller. The machine may start unexpectedly and cause personal injury or damage to the machine. Select a stitch. 6 CAUTION ● After adjusting the stitch width, slowly turn the handwheel toward you (counterclockwise) and check that the needle does not touch the presser foot. If the needle hits the presser foot, the needle may bend or break. ● When using the twin needle, make sure the stitch width is not set above "2.5" since this may cause the needle to hit the needle plate and break. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
30
————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————
2
■
Attaching the extra spool pin
Insert the extra spool pin onto the end of the bobbin
winder shaft. Install the second thread spool onto
the extra spool pin.
■
Twin needle threading
You should thread each needle separately.
Note
●
You cannot use the needle threader to
thread the twin needle. Instead, thread the
twin needle by hand, from front to back.
Using the needle threader may damage the
machine (see page 24).
1
Thread the upper thread for the right side
in the same way that the upper thread for
the left side was threaded.
1
Thread guide
•
For details, refer to step
1
through
0
of
“Upper threading” (page 20).
2
Thread the left needle.
3
Thread the right needle.
Thread the right needle in the same way that
you threaded the left needle using the thread
from the spool on the extra spool pin, but do not
pass the thread through the guide above the
needle before you pass it through the eye of the
right needle.
1
Left needle thread passes through the needle
bar thread guide
2
Right needle thread passes in front of the needle
bar thread guide
3
Needle bar thread guide
4
Attach zigzag foot “J”.
For details on changing the presser foot, refer
to “Changing the presser foot” on page 8.
CAUTION
5
Turn on the machine.
CAUTION
6
Select a stitch.
CAUTION
1
Bobbin winder shaft
2
Extra spool pin
3
Thread spool
1
●
When using the twin needle, be sure to
attach zigzag foot “J”, otherwise the
needle may break or the machine may be
damaged.
●
Do not turn on the machine while pressing
down the foot controller. The machine
may start unexpectedly and cause
personal injury or damage to the machine.
●
After adjusting the stitch width, slowly
turn the handwheel toward you
(counterclockwise) and check that the
needle does not touch the presser foot. If
the needle hits the presser foot, the
needle may bend or break.
●
When using the twin needle, make sure
the stitch width is not set above “2.5”
since this may cause the needle to hit the
needle plate and break.
1
3
2