Brother International TZ1-B652 Instruction Manual - English - Page 6

Needle

Get Brother International TZ1-B652 PDF manuals and user guides View all Brother International TZ1-B652 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Needle Use the needle No. DB X 1 (#9, #11, #14, #16, #18). The needle set to the machine as the standard accessory is No. DB X1 (#14). Needle number is marked on the haft of the needle. Needle clamp Marking position Groove Tighten Loosen To change the needle 1 . Raise the needle bar (1) up highest. 2. Use a screwdriver to loosen the needle clamp screw (2). 3. Pul l 'out the needle (3) downward. 4. Hold a new needle (4) with its groove (B) facing your side. (Direct the cutout (A) toward the presser bar.) 5. Insert the needle into the needle bar's needle hole al l the way up. 6. Tighten the needle clamp screw (2) securely by means of a screwdriver. 7. Turn the balance wheel slowly and ascertain that the needle point falls right in the center of the needle hole. Needle eye Needle head Pa allel To check the needle 1 . The sewing needle must be always straight and sharp to have smooth sewing. 2. To check if the needle is bent, put the flat side of the needle down on a slide plate as shown in left figure. -4-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Needle
Use
the
needle
No.
DB
X
1
(#9,
#11,
#14, #16,
#18).
The
needle
set
to
the
machine
as
the
standard
accessory
is
No.
DB
X1
(#14).
Needle
number
is
marked
on
the
haft
of
the
needle.
Needle
clamp
Tighten
Loosen
Marking
position
Groove
Needle
eye
Needle
head
Pa
al
lel
To
change
the
needle
1
.
Raise
the
needle
bar
(1)
up
highest.
2.
Use
a
screwdriver
to
loosen
the
needle
clamp
screw
(2).
3.
Pul
l
'out
the
needle
(3)
downward.
4.
Hold
a
new
needle
(4)
with
its
groove
(B)
facing
your
side.
(Direct
the
cutout
(A)
toward
the
presser
bar.)
5.
Insert
the
needle
into
the
needle
bar's
needle
hole
al
l
the
way
up.
6.
Tighten
the
needle
clamp
screw
(2)
securely
by
means
of
a
screwdriver.
7.
Turn
the
balance
wheel
slowly
and
ascertain
that
the
needle
point
fal
ls
right
in
the
center
of
the
needle
hole.
To
check
the
needle
1
.
The
sewing
needle
must
be
always
straight
and
sharp
to
have
smooth
sewing.
2.
To
check
if
the
needle
is
bent,
put
the
flat
side
of
the
needle
down
on
a
slide
plate
as
shown
in
left
figure.
—4—