Brother International XL-6452 Users Manual - English - Page 78

Monogramming and, Embroidering

Get Brother International XL-6452 PDF manuals and user guides View all Brother International XL-6452 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

USING ATTACHMENTS AND APPLICATIONS UTILISATION DES ACCESSOIRES ET LEURS APPLICATIONS USO DE ACCESORIOS Y APLICACIONES A Monogramming and Embroidering Pattern Stitch Length Stitch Width Any Any Foot None PREPARING FOR MONOGRAMMING AND EMBROIDERING 1. Remove the power supply plug from the outlet. And place the darning plate on the needle plate as shown in fig. A. Connect the power supply plug into a wall outlet. 2. Set the Pattern Selection Dial to the appropriate Zigzag Stitch setting. 3. Draw the lettering (for monogramming) or design (for embroidering) on the surface of the fabric. 4. Stretch the fabric between embroidery hoops as firmly as possible with the underside of the fabric on the bottom of the inside hoop. 5. Place the work under the needle and lower the presser bar with the foot removed. 6. Pull the lower thread up through the work at the starting position by turning the balance wheel and make a few holding stitches. 7. Grip the hoop with the thumb and forefingers of both hands while pressing the fabric with the middle and third fingers and supporting the outside of the hoop with your smaller fingers. MONOGRAMMING 1. Sew, moving the hoop slowly along the lettering at a constant speed. 2. Secure with a few straight stitches at the end of the last letter. EMBROIDERING 1. Stitch the outline of the design by moving the embroidery hoop. 2. Fill in the design alternating from the outline of the design to the inside and from the inside to the edge of the outline until the design is completely filled in. Keep the stitching close together. NOTE: A long stitch is made by moving the embroidery hoop rapidly and a short stitch is made by moving it slowly. 3. Secure with a few Straight Stitches at the end of the design. 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
67
USING ATTACHMENTS AND APPLICATIONS
UTILISATION DES ACCESSOIRES ET LEURS APPLICATIONS
USO DE ACCESORIOS Y APLICACIONES
Monogramming and
Embroidering
Pattern
Stitch Length
Stitch Width
Foot
Any
Any
None
PREPARING FOR MONOGRAMMING AND EMBROIDERING
1.
Remove the power supply plug from the outlet.
And place the
darning plate on the needle plate as shown in
fig. A
. Connect the
power supply plug into a wall outlet.
2.
Set the Pattern Selection Dial to the appropriate Zigzag Stitch
setting.
3.
Draw the lettering (for monogramming) or design (for embroi-
dering) on the surface of the fabric.
4. Stretch the fabric between embroidery hoops as firmly as
possible with the underside of the fabric on the bottom of the
inside hoop.
5.
Place the work under the needle and lower the presser bar with
the foot removed.
6.
Pull the lower thread up through the work at the starting position
by turning the balance wheel and make a few holding stitches.
7.
Grip the hoop with the thumb and forefingers of both hands while
pressing the fabric with the middle and third fingers and support-
ing the outside of the hoop with your smaller fingers.
MONOGRAMMING
1.
Sew, moving the hoop slowly along the lettering at a constant
speed.
2.
Secure with a few straight stitches at the end of the last letter.
EMBROIDERING
1.
Stitch the outline of the design by moving the embroidery hoop.
2.
Fill in the design alternating from the outline of the design to the
inside and from the inside to the edge of the outline until the
design is completely filled in. Keep the stitching close together.
NOTE:
A long stitch is made by moving the embroidery hoop rapidly and a
short stitch is made by moving it slowly.
3.
Secure with a few Straight Stitches at the end of the design.
A