Home » Campbell Scientific Manuals » Electronics Accessories » Campbell Scientific CR10X » Manual Viewer

Campbell Scientific CR10X TD Operating System Addendum for CR510, CR10X, and C - Page 47

PakBus Get/Send Locations P190

View all Campbell Scientific CR10X manuals

Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Section 12. Program Control Instructions Radio Settings CR205 Power Mode and Header RF400 on CR10X or CR23X Beacon Interval RF400 on computer LoggerNet Settings When RF400 with direct access to network is connected to computer. Stand Alone SendGetData P190 Wireless Sensor P193 Datalogger Radio address, net address, and hop sequence must be the same in all CR2xxs and RF400s in the network. Because only one header length can be set for a radio, only one power cycling interval should be used in network; i.e., do not mix 8 second and 1 second interval radio power cycling. RF on (no cycling) is specified where necessary below. Select power mode for Select power mode for NO HEADER. appropriate response appropriate response RfpinEn (lowest power) time and current drain. time and current drain. or to allow communi- Header must match cation with computer for called station's cycle. checking station, down- loading program: RF8_Sec or RF1_sec. Router, if used, must Router, if used, must RF on, header to match send appropriate header send appropriate header CR205 setting to allow contacting CR205 0 0 0 RF on, header to match RF on, header to match RF on, header to match neighbors' settings neighbors' settings neighbors' settings For each datalogger: For each datalogger For each master with stored data: datalogger: Com Com Com -PbusPort -PbusPort -PbusPort -logger -logger -logger PakBus Get/Send Locations (P190) A program control instruction that sends data to or retrieves data from another datalogger in a PakBus network. This instruction can also be used to issue commands to Modbus devices, where the datalogger acts as a Modbus master. 1: PakBus - Get/Send Locations (P190) 1: 00 Port 2: 0000 Address 3: 00 Command 4: 0000 Security 5: 0000 Remote Loc/Coil/Register 6: 0000 Swath 7: 0000 Local Loc 8: 0000 Result Code Loc 12-3

Section	Page
Revision and Copyright Information	1
TD and PakBus Operating System Addendum for CR510, CR10X, and CR23X Manuals	3
AD1 Major Differences	3
AD2 Overview of Data Storage Tables	4
AD3 Converting an existing program to Table Based OS	4
AD3.1 Programming changes	4
AD3.2 Making the Changes with Edlog	5
AD4 Summary of Differences from the Datalogger Manual:	6
MEASUREMENT AND CONTROL MODULE OVERVIEW	9
OV4. PROGRAMMING THE CR10X	9
OV4.1 FUNCTIONAL MODES	9
OV4.2 KEY DEFINITION	9
OV4.3 PROGRAMMING SEQUENCE	10
OV4.4 INSTRUCTION FORMAT	10
OV4.5 ENTERING A PROGRAM	11
OV5. PROGRAMMING EXAMPLES	11
OV5.1 SAMPLE PROGRAM 1	11
OV5.2 SAMPLE PROGRAM 2	13
OV5.3 EDITING AN EXISTING PROGRAM	15
OV6. DATA RETRIEVAL OPTIONS	15
SECTION 1. FUNCTIONAL MODES	17
1.5 MEMORY ALLOCATION - ?A	17
1.5.1 INTERNAL MEMORY	17
1.5.2 ?A MODE	18
MEMORY TESTING AND SYSTEM STATUS - ?B	19
1.7 *C MODE -- SECURITY	19
1.8 *D MODE – TRANSFER PROGRAMS, GENERAL SETTING	19
1.8.1 ERASING CURRENT PROGRAM	20
1.8.2 PROGRAM TRANSFER WITH STORAGE MODULE	20
1.8.3 FULL/HALF DUPLEX	20
1.8.4 SET DATALOGGER ID	20
1.8.5 SETTING POWERUP OPTIONS	20
1.8.6 SET INITIAL BAUD	21
1.8.7 SET PROGRAM COMPILE OPTION	21
1.8.8 SET PAKBUS ADDRESS	21
1.8.9 ALLOCATE MEMORY FOR GENERAL PURPOSE FILES	22
1.8.10 VIEW ROUTING TABLE	22
1.8.11 SET PAKBUS ROUTER BEACON INTERVAL	22
1.8.12 PAKBUS NEIGHBOR FILTER	22
1.9 *9 DATA TABLES SIZES.	23
SECTION 2. INTERNAL DATA STORAGE	25
2.1 FINAL STORAGE AND DATA TABLES	25
2.1.1 TIME AND TIMESTAMPS	25
2.1.2 RECORD NUMBERS	26
2.1.3 TABLES AND FIELDS.	26
2.2 DATA OUTPUT FORMAT AND RANGE LIMITS	27
2.2.1 RESOLUTION AND RANGE LIMITS	27
2.2.2 HIGH RESOLUTION FINAL STORAGE DATA, INPUT, AND INTERMEDIATE STORAGE DATA FORMAT	27
2.3 DISPLAYING STORED DATA ON KEYBOARD/DISPLAY *7 MODE.	27
SECTION 3. INSTRUCTION SET BASICS	29
SECTION 8. PROCESSING AND PROGRAM CONTROL EXAMPLES	31
8.1 COMPUTATION OF RUNNING AVERAGE	31
8.2 RAINFALL INTENSITY	32
8.3 USING CONTROL PORTS AND LOOP TO RUN AM416 MULTIPLEXER	33
8.4 INTERRUPT SUBROUTINE USED TO COUNT SWITCH CLOSURES (RAIN GAGE)	35
8.5 SDM-A04 ANALOG OUTPUT MULTIPLEXER TO STRIP CHART	36
8.6 CONVERTING 0-360 WIND DIRECTION OUTPUT TO 0-540 FOR STRIP CHART	37
8.7 LOGARITHMIC SAMPLING USING LOOPS	37
SECTION 9. INPUT/OUTPUT INSTRUCTIONS	41
SECTION 11. OUTPUT PROCESSING INSTRUCTIONS	43
SECTION 12. PROGRAM CONTROL INSTRUCTIONS	45
Wireless Networks	45
Datalogger Requirements	45
Communication Notes	45
PakBus Get/Send Locations (P190)	47
Port	48
Address	48
PakBus Communication	49
Modbus Communication	49
Command	49
Security	50
Remote Location/Coil/Register	50
PakBus Communication	50
Modbus Communication	50
Remote Location	51
PakBus Communication	51
Modbus Communication	51
Swath	51
PakBus Communication	51
Modbus Communication	51
Local Location	51
PakBus Communication	51
Modbus Communication	51
Result Code Location	52
Send Final Storage Data (P191)	52
Table ID	52
Flag	52
Send Message (P192)	52
Message Type	53
Wireless Network Master (P193)	53
Number of Remotes	54
First Remote Address	54
Time into Transmit Interval	54
Example	54
Transmit Interval	54
Example	55
Transmit Delay Between Remotes	55
Example	55
Swath to Receive	55
First Location for Data Received	55
Swath to Send	56
First Location to Send	56
Result Code Location	56
Seconds Until Transmit (P194)	56
Location with Seconds Until Transmit	57
Use Remote Clock Report (P195)	57
Address	57
Wireless Network Remote (P196)	57
Swath to Receive From Master	58
First Location for Data Received	58
Security	58
Swath to Send	58
First Location to Send	58
Result Code Location	59
Force Route (P197)	59
Neighbor's Address	59
Hops	59
Set Setting (P198)	59
Result Location	60
Routing Table Information (P199)	60
Example	60
PakBus Settings (Options \| PakBus Settings)	61
Network	61
Beacon Intervals	61
Neighbor Filter	62

Match case Limit results 1 per page

Section 12.

Program Control Instructions

12-3

Stand Alone

Datalogger

SendGetData P190

Wireless Sensor P193

Radio Settings

Radio address, net address, and hop sequence must be the same in all CR2xxs

and RF400s in the network. Because only one header length can be set for a

radio, only one power cycling interval should be used in network; i.e., do not

mix 8 second and 1 second interval radio power cycling. RF on (no cycling) is

specified where necessary below.

CR205

Power Mode and

Header

Select power mode for

appropriate response

time and current drain.

Select power mode for

appropriate response

time and current drain.

Header must match

called station’s cycle.

NO HEADER.

RfpinEn (lowest power)

or to allow communi-

cation with computer for

checking station, down-

loading program:

RF8_Sec or RF1_sec.

RF400 on CR10X

or CR23X

Router, if used, must

send appropriate header

Router, if used, must

send appropriate header

RF on,

header to match

CR205 setting to allow

contacting CR205

Beacon Interval

RF400 on computer

RF on,

header to match

neighbors’ settings

RF on,

header to match

neighbors’ settings

RF on,

header to match

neighbors’ settings

LoggerNet Settings

When RF400 with direct

access to network is

connected to computer.

For each datalogger:

Com

-PbusPort

-logger

For each datalogger

with stored data:

Com

-PbusPort

-logger

For each master

datalogger:

Com

-PbusPort

-logger

PakBus Get/Send Locations (P190)

A program control instruction that sends data to or retrieves data from another

datalogger in a PakBus network. This instruction can also be used to issue

commands to Modbus devices, where the datalogger acts as a Modbus master.

PakBus - Get/Send Locations (P190)

1: 00

Port

2: 0000

Address

3: 00

Command

4: 0000

Security

5: 0000

Remote Loc/Coil/Register

6: 0000

Swath

7: 0000

Local Loc [ ______________ ]

8: 0000

Result Code Loc [ ______________ ]