Home » Campbell Scientific Manuals » Electronics Accessories » Campbell Scientific CWS220 » Manual Viewer

Campbell Scientific CWS220 Wireless Sensor Network (CWB100, CWS220, and CWS900 - Page 19

CWS220 Specifications

View all Campbell Scientific CWS220 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Wireless Sensor Network Terminal Block Connector: Bi-Directional Serial datalogger connection USB Port: Computer connection for configuration Antenna: RPSMA antenna connection Memory: Can store data table for up to 50 wireless sensors. Operating Temperature Range: -25° to +50°C (-13° F to + 122°F) Terminal Block Pin-Out: I/O Name Description In +12V 12V Supply n/a GND Supply Ground i/o DATA/A CPI "A" i/o B CPI "B" n/a ISO_GND CPI Signal Reference 2.2.3 CWB100 Environmental Specifications Temperature Range: Humidity Range: -25° to +50°C (-13° F to + 122°F) Store and use in non-condensing (desiccated) environment. 2.2.4 Datalogger Compatibility The CWB100 is compatible with Campbell Scientific datalogger models CR800-series, CR1000, and CR3000. These dataloggers use the CRBasic instruction CWB100() to communicate with the CWB100. See Section 5 for programming details. Datalogger operating systems that support the CWB100 and CWS sensors are: CR800-Series CR800.Std.21 and higher CR1000 CR1000.Std.21 and higher CR3000 CR3000.Std.21 and higher 2.3 CWS220 Specifications 2.3.1 CWS220 Physical Specifications Dimensions: 15 cm x 6 cm x 4.5 cm (6" x 2.4" x 1.8") Weight: 270 g (9.6 oz) 11

Section	Page
Revision and Copyright Information	1
Warranty	3
Assistance	4
Table of Contents	5
Wireless Sensor Network	9
1. Understanding a Wireless Sensor Network	9
1.1 General Description	9
1.2 CWB100 Wireless Base Station	10
1.3 CWS220 Wireless Infrared Radiometer	11
1.4 CWS655 Wireless Water Content Reflectometer	12
1.5 CWS900 Wireless Sensor Interface	13
2. Specifications	16
2.1 Wireless Sensor Network Radio	16
2.1.1 Electrical	16
2.1.2 Typical RF Range	17
2.1.3 RSSI	17
2.1.4 Service Discovery Protocol	17
2.1.5 Antenna Options	18
2.2 CWB100 Specifications	18
2.2.1 CWB100 Physical Specifications	18
2.2.2 CWB100 Electrical Specifications	18
2.2.3 CWB100 Environmental Specifications	19
2.2.4 Datalogger Compatibility	19
2.3 CWS220 Specifications	19
2.3.1 CWS220 Physical Specifications	19
2.3.2 CWS220 Electrical Specifications	20
2.3.3 CWS220 Environmental Specifications	20
2.4 CWS655 Specifications	20
2.4.1 CWS655 Physical Specifications	20
2.4.2 CWS655 Electrical Specifications	20
2.4.3 CWS655 Environmental Specifications	21
2.5 CWS900 Specifications	21
2.5.1 CWS900 Physical Specifications	21
2.5.2 CWS900 Electrical Specifications	21
2.5.3 CWS900 Environmental Specifications	22
3. Getting Started: Creating a Wireless Sensor Network	22
3.1 Hardware and Software Required for a WSN	22
3.1.1 A205 CWS to PC Interface	22
3.1.2 Required Cables	23
3.1.3 Configuration CD	24
3.1.4 Configuration Software	24
3.1.5 Driver Installation	24
3.2 Creating a Model of the WSN	24
3.2.1 Wireless Sensor Planner and Network Planner	24
3.2.2 Installing Wireless Sensor Planner	25
3.2.3 Using Wireless Sensor Planner	25
3.2.3.1 Simple WSN Example	26
Placing Devices on the Drawing Canvas	26
Adding Communication Links to Devices	27
3.3 Configuring the Devices in the WSN	29
3.3.1 Configuring the CWB100	29
3.3.2 Configuring the CWS655	31
3.3.3 Configuring the CWS900	32
3.4 Sending the Sensor Configuration File to the Datalogger	32
3.5 Programming the Datalogger	33
Determining Size of the Array	34
Determining the Scan Rate	34
Inserting the CWB100() Instruction	34
Finishing the Program	35
3.6 Connecting the CWB100 to the Datalogger	35
3.7 Powering CWS Sensors and Initiating Auto-discovery	35
3.8 Verify that Data is being Transmitted	36
3.9 Physical Connections	36
3.9.1 Connecting the Base Station to the Datalogger	36
3.9.2 Connecting Sensors to the CWS900	37
4. Programming the Datalogger	37
4.1 Array Declaration	37
4.2 CWB100() Instruction	38
4.2.1 Configuration String	39
4.2.2 Field Names	40
4.2.3 Status Monitoring	40
4.3 ArrayIndex() Instruction	41
4.4 CWB100RSSI() Instruction	42
4.5 CWB100Routes() Instruction	42
4.6 Program Example	43
5. CWS Button and LED Behavior	45
5.1 Sensor Link to Base Station	45
5.2 Sensor Battery Voltage	45
5.3 CWS Sensor Search for Base Station	45
6. Testing the Network	46
7. Maintenance	48
7.1 Replacing a Sensor in the Network	49
7.2 Stopping or Loading a New Datalogger Program	49
8. Troubleshooting	50
Appendix A. Using DevConfig for CWS Setup	53
Appendix B. Measurement Names and Meanings	57
B.1 CWS220 Default Names	57
B.2 CWS655 Default Names	57
B.3 CWS900 Default Names	58
B.3.1 Wind Vector Calculations	60
Measured raw data:	60
Calculations:	60
Appendix C. Battery Life	65
C.1 Battery Characteristics	65
C.2 Effect of Polling Interval and Repeaters on Battery Life	65
C.3 RF Connection Type Setting	66
C.4 Repair of a Lost Connection	67