Canon DR 5010C Easy Start Guide - Page 2

☞Continued from front side 12. When all installations are complete, the installation completed screen appears. Click [Exit] to exit the installer. Click [Back] to return to the menu screen. 6-2 Connect the scanner to your computer with the SCSI cable. SCSI cable is not supplied. Acquire a SCSI cable beforehand that matches the shape of the connectors on your SCSI card and the scanner. This completes the software installation. Next, you need to connect the scanner to your computer. (☞STEP4) Connecting the Scanner to Your PC The scanner can be connected to a computer in two ways: by USB connection to a standard USB port on the computer, or by SCSI connection to a SCSI card installed in one of the computer's expansion slots. Select a connection method appropriate to your computing environment. Imprinter Connector SCSI ID Dip Switches USB Connector Power Connector SCSI Connector (Half-pitch 50-pin, pin-type) Warning ❏ Do not use both a USB connection and a SCSI connection at the same time. ❏ Use only the supplied power cord. ❏ Connect the scanner to your computer while the scanner is turned OFF. ❏ Before connecting the scanner with a SCSI cable, turn your computer OFF. ❏ A SCSI cable is not supplied. Acquire a SCSI cable beforehand that matches the shape of the connectors on your SCSI card and the scanner. 1. When connecting the scanner with a SCSI cable, turn your computer OFF. 2. Make sure the scanner's power switch is in the OFF position. If the power switch is in the ON position, press the switch to turn it to the OFF position. Power Switch OFF Position ON Position 3. Plug the power cord into the power connector on the rear of the scanner (1). 4. Plug the power cord into the power outlet (2). 5. When connecting the scanner with a USB cable, use the supplied USB cable. Type A Type B 6. Follow the steps below when connecting the scanner to your computer with a SCSI cable. 6-1 Turn OFF your computer. Make sure your computer is turned OFF before connecting the SCSI cable. Warning ❏ When using the scanner in a daisy chain connection with other SCSI devices, pay attention to the following points: ● The default setting for the SCSI ID is "SCSI ID=2." Set the dip switches so that the scanner's SCSI ID is different from all other SCSI devices on the chain. Default Position (SCSI ID=2) OFF ON 12 SCSI ID 2 3 4 5 SW1 OFF ON OFF ON Dip Switches SW2 OFF OFF ON ON ● The scanner has a built-in SCSI terminator that is permanently set to [ON]. When using the scanner in a daisy chain connection, make sure that it is connected as the terminating device and that the terminators of all other SCSI devices in the chain have been set to [OFF]. The scanner is now connected to your computer. Next, you need to turn on the scanner and ensure Windows recognizes it. (☞STEP5) Turning On the Power (Scanner Recognition) When you turn the scanner connected to the PC ON, the plug-and-play function recognizes the scanner, and the device driver is automatically installed. Warning ❏ When the scanner is connected by a SCSI cable, always turn on the scanner before the computer. Turning on the computer first may prevent it from recognizing the scanner properly. ❏ Log on to Windows with an account that has administrator privileges. ❏ Wait at least 10 seconds before turning the scanner on again after turning it off. ❏ If the scanner will not be used for an extended period, be sure to unplug it from the power outlet for safety. 1. Check the connection between the scanner and the computer. 2. Press the power switch to turn the scanner ON (when connecting by SCSI). The power indicator and start key indicator both light green. 3. Turn ON your computer. Start key Power indicator Power Switch ON Position 4. Windows recognizes the DR-5010C as new hardware and performs installation automatically. (Windows 2000) (Windows XP) (Windows Vista) Note ● For Windows XP/Vista, a balloon help pop-up appears when installation is finished. (Windows XP) (Windows Vista) ● The installation finished message does not appear in Windows 2000. ● The scanner is registered on the computer as "CANON DR-5010C USB" (or "CANON DR-5010C SCSI") in the "Imaging Device" directory of the Device Manager. The scanner is now correctly recognized by your computer. Next, you need to select the scanner with the scanning software. (☞STEP6) Selecting the Scanner You must select your scanner before using it with an ISIS- or TWAIN-compatible scanning application. The menus and procedures for selecting the scanner are different for each application. For details, refer to the manual for your scanning application when selecting the scanner. This section explains the procedure for selecting the scanner with "CapturePerfect 3.0". For details on how to use CapturePerfect 3.0, refer to the "CapturePerfect 3.0 Operation Guide" in the Programs menu of Windows. 1. Launch CapturePerfect 3.0 from the Programs menu in Windows. 2. Select [Select Scanner] from the Scan menu. The Scanner Selection dialog box appears. 3. Select [Canon DR-5010C] and click [OK]. Note ● Windows 2000/XP/Vista possess an event feature that allows you to launch a scanning application with the start key on the scanner. CapturePerfect 3.0 supports this feature and, once setup is complete, can be launched by pressing the scanner's start key. ● When multiple applications that support the event feature are installed, pressing the start key displays an Event on device dialog box for selecting the desired application. ● You can change the event settings to specify a priority application from among multiple applications or to turn off the event feature. For details, refer to "Setting the Event Function" on page 40 of the User's Guide. The setup is now complete This completes the setup of the DR-5010C. Details on how to use the DR-5010C are described in the User's Guide packaged with the scanner. Before you start using the scanner, make sure to thoroughly read the User's Guide.