Home » Canon Manuals » Projectors » Canon LV-7370 » Manual Viewer

Canon LV-7370 LV-7370 User Manual - Page 91

PC Control Codes and Cable Connection

Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

❼ PC Control Codes and Cable Connection PC Control Codes Function Code Data POWER ON 02H 00H 00H 00H 00H 02H POWER OFF 02H 01H 00H 00H 00H 03H INPUT SELECT Computer 1 02H 03H 00H 00H 02H 01H 01H 09H INPUT SELECT Computer 2 (Digital) 02H 03H 00H 00H 02H 01H 1AH 22H INPUT SELECT Computer 2 (Analog) 02H 03H 00H 00H 02H 01H 02H 0AH INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH INPUT SELECT S-VIDEO 02H 03H 00H 00H 02H 01H 0BH 13H BLANK ON 02H 10H 00H 00H 00H 12H BLANK OFF 02H 11H 00H 00H 00H 13H SOUND MUTE ON 02H 12H 00H 00H 00H 14H SOUND MUTE OFF 02H 13H 00H 00H 00H 15H NOTE: Contact your local dealer for a full list of the PC Control Codes if needed. Cable Connection Communication Protocol Baud rate 19200 bps Data length 8 bits Parity No parity Stop bit One bit X on/off None Communications procedure............Full duplex NOTE: Depending on the equipment, a lower baud rate may be recommended for long cable runs. SERVICE PORT Connector (D-SUB 9P) To TxD of PC To RxD of PC To GND of PC 7. Appendix 12345 6789 To RTS of PC To CTS of PC NOTE 1: Pins 1, 4, 6 and 9 are no used. NOTE 2: Jumper "Request to Send" and "Clear to Send" together on both ends of the cable to simplify cable connection. NOTE 3: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps. 82

Section	Page
INDEX	1
Important Information	2
Table of Contents	8
1. Introduction	10
(1) What's in the Box?	10
(2) Introduction to the Projector	11
Congratulations on Your Purchase of The Projector	11
Features you'll enjoy:	11
About this user's manual	12
(3) Part Names of the Projector	13
Front/Top	13
Rear	13
Top Features	14
Terminal Panel Features	15
(4) Part Names of the Remote Control	16
Battery Installation	18
Remote Control Precautions	18
Operating Range for Wireless Remote Control	18
2. Installation and Connections	19
(1) Setting Up the Screen and the Projector	20
Selecting a Location (LV-7375/LV-7370/LV-7275)	20
Throw Distance and Screen Size	20
Selecting a Location (LV-8300)	21
Throw Distance and Screen Size	21
(2) Making Connections	23
Enabling the computer’s external display	23
Connecting Your PC or Macintosh Computer	23
When Viewing a DVI Digital Signal	25
Using Two Analog Computer Inputs Simultaneously	26
Connecting an External Monitor	27
Connecting Your Audio-Video Equipment with Component Output	28
Connecting Your Audio-Video Equipment with Video/S-Video Output	29
Connecting a Digital Video Signal	30
Connecting to a Network	31
Connecting the Supplied Power Cord	32
3. Projecting an Image (Basic Operation)	33
(1) Turning on the Projector	33
Note on Startup screen (Menu Language Select screen)	34
(2) Selecting a Source	35
Selecting the computer or audio-video equipment	35
Selecting Default Source	36
(3) Adjusting the Picture Size and Position	37
Adjusting the Tilt Foot	38
Zoom	39
Focus	39
(4) Correcting Keystone Distortion	40
Correcting Keystone Distortion	40
Adjusting with buttons on the cabinet	40
Adjusting with the Remote Control	41
Adjusting with the Auto Keystone Function	42
(5) Automatically Optimizing on RGB Image	43
Adjusting the Image Using Auto PC adjustment	43
(6) Turning Up or Down Volume	43
(7) Turning off the Projector	44
(8) After Use	45
4. Convenient Features	46
(1) Turning off the Image and Sound	46
(2) Freezing a Picture	46
(3) Enlarging a Picture	46
(4) Preventing the Unauthorized Use of the Projector [Password]	47
To enable the Password function:	47
To turn on the projector when Password is enabled:	48
To disable the Password function:	49
(5) Network and Alert Mail Settings by Using an HTTP Browser	50
Overview	50
Preparation Before Use	50
Network Settings	51
Alert Mail Setting	52
List of Error Messages	53
5. Using On-Screen Menu	54
(1) Using the Menus	54
(2) Menu Elements	55
(3) List of Menu Items	56
(4) Menu Descriptions & Functions [Input]	58
Computer 1	58
Computer 2 (Digital & Analog)	58
VIDEO	58
S-VIDEO	58
(5) Menu Descriptions & Functions [Adjustment]	59
[Image]	59
[Image mode]	59
[Detail settings]	59
Selecting Reference Setting [Reference]	59
Selecting Gamma Correction Mode [Gamma]	59
Adjusting Color Temperature [Color temperature]	60
Adjusting White Balance [Brightness RGB/Contrast RGB]	60
Adjusting Brightness, Contrast, Sharpness, Color level and Color balance	60
Reset	60
[Input signal]	61
Adjusting Clock and Phase [Clock/Tracking]	61
Adjusting Horizontal/Vertical Position [Horizontal position/Vertical position]	62
Selecting Overscan Percentage [Overscan]	62
Selecting Aspect Ratio [Aspect]	63
Adjusting the Vertical Position of Image [D.image shift] (not available on LV-8300)	65
Selecting Video Filter Level [Video filter] (not available for Digital RGB, Video and S-Video)	65
(6) Menu Descriptions & Functions [Setup]	66
[General]	66
Enabling Auto Keystone [Auto keystone]	66
Correcting Vertical Keystone Distortion Manually [Keystone adjustment]	66
Saving Vertical Keystone Correction [Keystone save]	66
Selecting Wall Color Correction Mode [Screen color]	66
Selecting Lamp Mode [Lamp mode]	67
Setting Closed Caption [Closed caption]	67
Selecting Menu Language [Language]	67
[Menu]	68
Selecting Menu Color [Color select]	68
Selecting Menu Display Time [Display time]	68
Selecting a Color for Background [No signal screen]	68
Selecting Interval Time for Filter Message [Filter message]	68
[Installation]	69
Selecting Projector Orientation [Image flip H/V]	69
Disabling the Cabinet Buttons [Key lock]	69
Enabling Password [Password]	69
Selecting Communication Speed [Communication speed]	70
[Options (1)]	70
Setting Auto Adjust [Auto PC adjustment]	70
Enabling Fan Speed Mode [Fan mode]	70
[Input signal select]	71
Enabling or Disabling WXGA Mode [WXGA mode]	71
Enabling the deinterlace [Progressive]	71
Enabling Key Sound and Error Sound [Beep]	71
[Options (2)]	71
Setting Off Timer [Off timer]	71
Selecting Power-saving in [Standby mode]	71
Enabling Direct Power ON [Direct power on (AC)]	72
Turning On the Projector By Applying Computer Signal [Direct power on (Comp1)]	72
Enabling Power Management [Power management]	72
Selecting Default Source [Default source select]	72
(7) Menu Descriptions & Functions [Information]	73
[Usage time]	73
[Input signal]	74
[Wired LAN]	74
[Version]	74
(8) Menu Descriptions & Functions [Reset]	75
Resetting settings and adjustments [Reset]	75
Clearing adjustments and settings for the current signal [Current signal]	75
Clearing all the adjustments and settings [All data]	75
Clearing Networking Settings [Network settings]	75
Clearing Lamp Hour Meter [Lamp counter]	75
Clearing the Filter Usage Hours [Filter counter]	75
6. Maintenance	76
(1) Cleaning or Replacing the Filter	76
(2) Cleaning the Cabinet and the Lens	77
(3) Replacing the Lamp	78
7. Appendix	81
(1) Troubleshooting	81
Indicator Messages	81
Common Problems & Solutions	82
(2) Specifications	84
Optical	84
Electrical	84
Mechanical	85
Regulations	85
(3) Cabinet Dimensions	86
(4) Pin Assignments of D-Sub ANALOG IN-1 Input Connector	87
(5) Compatible Input Signal List	88
(6) Relationship between Screen Size and Projection distance	89
LV-7375/LV-7370/LV-7275	89
LV-8300	90
(7) PC Control Codes and Cable Connection	91
PC Control Codes	91
Cable Connection	91
SERVICE PORT Connector (D-SUB 9P)	91

Match case Limit results 1 per page

8³

7. Append±x

❼

PC Control Codes and Cable Connection

PC Control Codes

NOTE: Contact your local dealer for a full list of the PC Control Codes if needed.

Cable Connection

Communication Protocol

Baud rate

.........................................

19200 bps

Data length

......................................

8 bits

Parity

...............................................

No parity

Stop bit

............................................

One bit

X on/off

...........................................

None

Communications procedure

...........

Full duplex

NOTE: Depending on the equipment, a lower baud rate may be recommended for long cable runs.

SERVICE PORT Connector (D-SUB 9P)

Function

Code Data

POWER ON

02H

00H

02H

POWER OFF

02H

01H

00H

03H

INPUT SELECT Computer 1

02H

03H

00H

02H

01H

09H

INPUT SELECT Computer 2 (Digital)

02H

03H

00H

02H

01H

1AH

22H

INPUT SELECT Computer 2 (Analog)

02H

03H

00H

02H

01H

02H

0AH

INPUT SELECT VIDEO

02H

03H

00H

02H

01H

06H

0EH

INPUT SELECT S-VIDEO

02H

03H

00H

02H

01H

0BH

13H

BLANK ON

02H

10H

00H

12H

BLANK OFF

02H

11H

00H

13H

SOUND MUTE ON

02H

12H

00H

14H

SOUND MUTE OFF

02H

13H

00H

15H

NOTE 1: Pins 1, 4, 6 and 9 are no used.

NOTE 2: Jumper “Request to Send” and “Clear to Send” together on both ends of the cable to simplify cable connection.

NOTE 3: For long cable runs it is recommended to set communication speed within projector menus to 9600 bps.

to gnd oF PC

to rxd oF PC

to txd oF PC

to rts oF PC

to Cts oF PC