Canon LV-WX300USTI User Manual - Page 58

Maintenance and Security, Replacing the Projection Lamp

Get Canon LV-WX300USTI PDF manuals and user guides View all Canon LV-WX300USTI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

MAINTENANCE AND SECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer. parts No.LV-LP41 Warning:  If illumination suddenly stops, either when you turn the projector on or after it has been on for a while, the lamp may have ruptured. In this case, never attempt to replace the lamp by yourself. Always request service from the Canon Customer Support Center. Additionally, with ceilingmounted projectors, the lamp may fall out when you open the lamp cover or while you are attempting to replace it.  During replacement, stand to the side of the lamp cover, not directly under it. If the lamp ruptures and you accidentally inhale or get pieces in your eyes or mouth, consult a doctor immediately.  If the lamp ruptures, dust and gas (containing mercury vapor) may come out of the exhaust vents. If this happens, immediately open the windows and doors to provide ventilation to the room. If you inhale any gas emitted from the lamp or it has come into contact with your eyes or mouth, consult a doctor immediately. Caution: When replacing the lamp, turn off the projector, wait until the cooling fan stops, disconnect the power plug from the electrical outlet, and let the projector stand for at least 45minutes. Otherwise, you may get burned because the main unit is very hot immediately after the projector is turned off. Caution:  Be sure to use the specified lamp.  Contact the Canon Customer Support Center for further information. This can also be purchased from the Canon website.  Do not touch the inner glass surface when you replace the lamp. Doing so may cause deterioration to the projector's performance.  Be sure to handle the lamp carefully and correctly since it may break during use if it has been scratched or subjected to impact. If the lamp ruptures, contact the Canon Customer Support Center.  When replacing the lamp, do not remove any screws other than those specified. 1. Remove the single screw on the lamp compartment cover. - 52-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
—
52
—
M
AINTENANCE AND
S
ECURITY
Replacing the Projection Lamp
The projection lamp should be replaced when it burns out. It should only be replaced with a certified
replacement part, which you can order from your local dealer. parts No.LV-LP41
Warning:
If illumination suddenly stops, either when you turn the projector on or after it has been on for a
while, the lamp may have ruptured. In this case, never attempt to replace the lamp by yourself.
Always request service from the Canon Customer Support Center. Additionally, with ceiling-
mounted projectors, the lamp may fall out when you open the lamp cover or while you are
attempting to replace it.
During replacement, stand to the side of the lamp cover, not directly under it. If the lamp
ruptures and you accidentally inhale or get pieces in your eyes or mouth, consult a doctor
immediately.
If the lamp ruptures, dust and gas (containing mercury vapor) may come out of the exhaust
vents. If this happens, immediately open the windows and doors to provide ventilation to the
room. If you inhale any gas emitted from the lamp or it has come into contact with your eyes or
mouth, consult a doctor immediately.
Caution:
When replacing the lamp, turn off the projector, wait until the cooling fan stops, disconnect the
power plug from the electrical outlet, and let the projector stand for at least 45minutes. Otherwise,
you may get burned because the main unit is very hot immediately after the projector is turned off.
Caution:
Be sure to use the specified lamp.
Contact the Canon Customer Support Center for further information. This can also be
purchased from the Canon website.
Do not touch the inner glass surface when you replace the lamp. Doing so may cause
deterioration to the projector’s performance.
Be sure to handle the lamp carefully and correctly since it may break during use if it has been
scratched or subjected to impact. If the lamp ruptures, contact the Canon Customer Support
Center.
When replacing the lamp, do not remove any screws other than those specified.
1.
Remove the single screw
on the lamp compartment
cover.