Canon PIXMA MP500 MP500 Easy Setup Instructions - Page 1
Canon PIXMA MP500 Manual
View all Canon PIXMA MP500 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Start Here Easy Setup Instructions Unpack the machine Please confirm bundled thing by the illustration printed on the flapped lid of the packing box. IMPORTANT Do not connect the USB cable until after the software is installed. See the rear side of this sheet for details. 1 Turn on the machine. 1 Connect the power cord, then press [ON/OFF]. (2) Connect the other end to the AC outlet. (3) Press [ON/OFF]. (1) Connect one end of the power cord to the rear of the machine. 2 Use [ ] or [ ] on the Operation Panel to select the language for the LCD, then press [OK]. 3 Install the ink tanks. QT7-0095-V03 1 Prepare the ink tanks. (1) Peel back the orange tab completely and remove the plastic wrapper from the ink tank. If the orange-colored protective film is not removed completely, problems with printing may occur. 2 Insert the ink tanks. (2) Twist off and discard the orange protective cap located on the bottom of the ink tank. Do not press! IMPORTANT electrical contacts Do not touch the electrical contacts. (1) Insert the ink tank into the rightmost slot. (2) Press the mark on the ink tank until it clicks into place and then its lamp lights red. Click Refer to the color guide on the print head lock lever. 3 Close the Inner Cover and the Scanning Unit (Printer Cover). (1) Press [ ] or [ ] to select the language. (2) Press [OK]. The language setting is only available for some countries. 3 If the message appears, go to Step 2, "Install the Print Head." 2 Install the Print Head. 1 Open the Paper Output Tray. (1) Press the Open Button. The Paper Output Tray opens. (2) Pull out the Paper Output Tray extension. 2 Lift the Scanning Unit (Printer Cover) until it locks into place. Lift the Scanning Unit (Printer Cover). IMPORTANT Be careful not to touch the buttons on the Operation Panel. 3 Open the Inner Cover. 4 Raise the lock lever. The Print Head Holder moves to the center. Do not touch the Print Head Holder while it is moving. Touch only the lock lever! Raise lock lever completely. Inner Cover Serial Number Location IMPORTANT (US Only) Write down the serial number located inside the machine. You will need this to register your products. 5 Prepare the Print Head. (1) Remove the print head from its package. IMPORTANT If the Scanning Unit (Printer Cover) is left open for more than 10 minutes, the Print Head Holder moves to the right. Close and reopen the Scanning Unit (Printer Cover) to return the Holder to the center. (2) Remove the protective cap and discard it. Do not touch! CAUTION There might be some transparent or light blue ink on the inside of the bag the print head comes in - this has no effect on print quality. Be careful not to get ink on yourself when handling these items. 6 Insert the Print Head. Do not touch! Insert. Remove the protective cap and discard it. CAUTION There might be some transparent or light blue ink on the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items. 7 Lower the lock lever. Lower the lock lever carefully and press it down. Click Close the Inner Cover. IMPORTANT Be careful not to touch the buttons on the Operation Panel. 4 Align the Print Head from the Operation Panel. This procedure is necessary to obtain a beautiful print result. The Print Head positions is automatically aligned. When the pattern shown on step 3-(3) is printed, the alignment is completed. Be sure to align the Print Head to ensure print quality. 1 Open the Paper Support, then pull out the extension. (1) Open the Paper Support. (2) Pull out the extension until it stops. (3) Pinch and slide the paper guide to the left end. 2 Load a few sheets of letter- or A4-size blank paper into the Auto Sheet Feeder. (2) Pinch and adjust the paper guide to the width of the stack. (1) Load the paper with the print side face up. Ensure the paper stack does not exceed the paper limit mark. Align the paper with the cover guide, then slide the paper guide toward the left edge of the paper. 3 Press [OK] to start Print Head alignment. (1) This message appears. (2) Make sure is selected, (3) The machine will then press [OK]. print the Print Head position pattern and automatically align the Print Head. The pattern is printed in black and blue. If this message does not appear after closing the Scanning Unit (Printer Cover), see "Aligning The Print Head automatically" in the User's Guide. • Print head alignment will take several minutes to complete. Do not start another operation here. • If the printed pattern matches the illustration, Print Head alignment is complete. You can change the language displayed on the LCD. For details, see "Language selection" in the User's Guide. Hardware setup and Print Head alignment is complete. If you are connecting the machine to a computer for use, see the rear side of this sheet for instructions on installing the software. "Windows" and "Internet Explorer" are trademarks of Microsoft Corporation, registered in the United States and other countries. "Macintosh" and "Mac" are trademarks of Apple Computer, Inc., registered in the U.S. and other countries. Specifications are subject to change without notice. xx2005A © CANON INC. 2005 © ArcSoft, Inc. All rights reserved for PhotoStudio. PRINTED IN THAILAND