Canon PIXMA mini260 Easy Setup Instructions - Page 1
Canon PIXMA mini260 Manual
View all Canon PIXMA mini260 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Start Here Easy Setup Instructions Unpack the Printer • Please confirm bundled thing by the illustration printed on the flapped lid of the packing box. • A USB cable is necessary to connect the printer with your computer. QT5-0755-V01 1 Prepare the printer 2 Install the Print Head a Place the printer on a flat and horizonal surface, and do not place any objects in front of the printer. Open the Paper Feed Tray and fold it in half. Place finger here to open the Paper Feed Tray and fold it in half. Paper Feed Tray a Unlock the Print Head Lock Lever by gently squeezing the tabs on both ends inward, and then raise the Print Head Lock Lever until it stops. Print Head Lock Lever 3 Install the ink tank a Remove the orange protective cap and discard it. Protective Cap Ink Ports The Paper Output Tray will open automatically. Caution Before turning on the printer, remove all of the shipping tapes. b Connect the power cord to the AC Adapter, and then plug the AC Adapter into the printer. Connect the other end of the power cord to a power outlet and then press the ON/OFF button. Important If the Alarm lamp is lit orange and an error message is displayed, see "Error Message Is Displayed on the LCD" in the Photo Printing Guide. c Use the { or } button or the Easy-Scroll Wheel on the Operation Panel to select the language for the LCD, then press the OK button. b Remove the Print Head from its package. Important There might be some transparent or light blue ink on the inside of the bag the Print Head comes in - this has no effect on print quality. Be careful not to get ink on yourself when handling these items. c Remove the orange protective cap from the Print Head and discard it. Protective Cap Print Head Nozzles Electrical Contacts Important Do not touch the Print Head nozzles and the electrical contacts. d Insert the Print Head. Electrical Contacts Important Do not touch the electrical contacts and the ink ports. b Insert the ink tank at a slant. Align the mark ▲ on the ink tank and the mark ▼ on the printer. c Press the mark on the ink tank until it clicks into place and then its lamp lights red. Important If the lamp does not light red after it is inserted, repeat steps 2 and 3. d Open the Printer Cover slightly, pull the Lock Lever to unlock, and then close the Printer Cover. Lock Lever 4 Align the Print Head a Load two sheets of the supplied 4" x 6" paper into the Auto Sheet Feeder with the whiter side facing front. Align the paper with the right side of the Auto Sheet Feeder, then slide the Paper Guide toward the left edge of the paper. Paper Guide Align the right side. Auto Sheet Feeder b When the message requesting head alignment is displayed on the LCD, press the OK button. The pattern is printed and the Print Head is aligned automatically. Easy-Scroll Wheel Important If you selected the wrong language by mistake, press the Back button to select again. d Slide the Lock Switch to the right, and then lift the Printer Cover. The cover will be locked if it is fully lifted. Align the mark and the mark on the Print Head on the printer. e Lower the Print Head Lock Lever carefully by pressing down the tabs on both ends until it clicks into place. a Click b Click Important Once you have installed the ink tank, wait for about 90 seconds until the printer has stopped making operating noises, before proceeding. Note An error message will be displayed on the LCD if the lock lever is not set properly or the ink tank is not installed properly. Open the Printer Cover and make sure that the lock lever is set properly or ink tank is installed properly. Note • The pattern is printed in black and blue. • Print Head alignment will take about 3 minutes to complete. Do not start another operation here. • If the Auto Head alignment cannot be executed correctly and a message is displayed on the LCD, please refer to "Error Message Is Displayed on the LCD" in the Photo Printing Guide. Hardware setup and Print Head alignment is complete. If you are connecting the printer to a computer, please see the back side of this sheet for Software Installation Instructions. Important Be sure to Lock the Print Head Lever until it "clicks" into place.