Home » Canon Manuals » Projectors » Canon REALiS LCOS WUX6700 » Manual Viewer

Canon REALiS LCOS WUX6700 WUX7500 WUX6700 WUX5800 Users Manual - Page 165

Power management duration, Direct power on, Motion blur reduction

View all Canon REALiS LCOS WUX6700 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 165 highlights

Menu Description Power management duration Specify how much time must pass before the light source goes off or the projector enters standby mode, depending on the [Power management mode] setting. Option Function 5 min. - 60 min. After 30 seconds without an input signal when the projector is idle, the projector starts displaying a countdown of the selected time. • If conditions that would start countdown are met while you are blanking projection, blanking is canceled. • Once countdown begins, audio output stops. Direct power on You can turn on the projector by connecting the power cable without pressing the POWER button. Option Function Off The POWER button must be pressed to turn the projector on. On You can turn on the projector by connecting the power cable only. • Before enabling direct power on, be sure to set [Power management mode] to an option other than [Disabled]. When [Disabled] is selected, [Direct power on] is not available. • After turning off the projector, wait at least 5 minutes before turning it on again. It may shorten the lamp life if you turn on the projector immediately after turning it off. • The projector is also equipped with a Direct Power Off feature. No damage is caused to the projector even if it is unplugged during projection to turn it off without pressing the POWER button. However, setting adjustments made immediately before unplugging the projector may not be stored. Motion blur reduction > [System settings] > [Motion blur reduction] Motion blur is blurring that occurs during video playback. Motion blur reduction can make this blurring less noticeable. Option Off Weak Strong Function Motion blur reduction is not performed. Reduce motion blur for fast-moving images. Note that images may be slightly darker, and flickering may occur. Reduce motion blur for images moving faster than with [Weak]. Note that images may be darker, and flickering may occur. • If setting the projector to [Strong] or [Weak] produces distracting flickering, set it to [Off]. • [Motion blur reduction] is not available in [DICOM SIM] image mode. The menu is grayed out. • Motion blur reduction is not available when [Lamp mode] is set to [Power saver 2]. Menu Guide Menu Description 163

Section	Page
How to Use This Manual	2
Table of Contents	5
Projector Highlights	7
Safety Instructions	9
Safety Symbols in this Manual	15
Precautions for Use	16
Power Supply	16
Installation and Use	18
Hazard Distance When Equipped with a Replacement Lens (IEC 62471-5)	20
Lamp	21
Remote Control Batteries	22
Handling	22
For Safe Use	24
Carrying and Installation	24
Before Installation	26
Precautions When Carrying / Shipping the Projector	26
Precautions for Installation	26
Do Not Use in the Following Environments	26
Do Not Touch the Lens with Bare Hands	27
Allow a 30 Min. Warm Up before Focus Adjustment (P46), if Possible	27
Install at a Sufficient Distance from Walls and Other Obstructions	27
Be Careful of Condensation	27
At Altitudes above 2,300 m (7,545.8'), Adjust the Settings	27
When Using Mounted on the Ceiling	28
Install Facing in the Correct Direction	29
Wireless LAN (Wi-Fi)	31
Countries and Regions Where Wireless LAN Use Is Permitted	31
Model Number	31
Open Source Software	32
Before Use	33
Included Accessories	33
Projector Part Names and Functions	34
Front Side	34
Rear Side	34
Bottom Side	34
Side Control	35
LED Indicators	35
Terminals and Connectors	37
Remote Control	38
Part Names and Functions	38
Installing Remote Control Batteries	40
Remote Control Operating Range	41
Using an Optional Wired Remote (RS-RC05)	42
Basic Guide	43
Projection Procedure	44
Step 1 Connect Other Equipment	45
Step 2 Turn the Projector On	46
Step 3 Select an Input Signal	47
Step 4 Adjust the Image	48
Adjusting the Computer’s Output Resolution	48
Focusing / Resizing the Image	48
Step 5 Select the Image Quality (Image Mode)	49
Image Modes	49
Projecting an Image in the DICOM SIM Mode	50
Turn the Projector Off	51
Convenient Projection Features	52
Convenient Features	52
Temporarily Blacking Out an Image	52
Freezing the Picture	52
Projecting a Test Pattern from the Menu	53
Specifying Power-Saving Settings	53
Adjusting the Volume	54
Muting the Sound	54
Zooming Part of an Image	55
Projecting Images on a USB Flash Drive	56
Description of USB File Browser	57
Selecting an Image for Projection	59
Controlling Images in Full-Screen Projection	59
Running a Slideshow of Data Saved in a USB Flash Drive	59
Projecting Two Images Side by Side	60
Switching Input Signals	61
Installation Guide	62
Installation Procedure	63
Relationship Between Projecting Distance and Image Size	63
Installing / Removing the Lens Unit	67
Installing the Lens Unit	68
Installation	70
Tabletop or Floor Installation (Lower Than the Screen)	70
Adjusting Peripheral Focus	74
Bringing Image Edges into Focus	74
Resetting Adjustment	76
High Installation, Ceiling Mounting, and Rear Projection	77
Connection Procedure	78
Connecting Other Equipment	78
HDMI Connections	78
DVI-I Connections	79
DisplayPort Connections	79
Analog PC-2 / COMPONENT Connections	80
LAN / HDBaseT Connections	81
Audio Input/Output Connections	81
Plugging the Projector In	82
Connecting to a Network	83
Network Connection Overview	83
Connection Methods	83
Wired Networks	83
Wireless Networks	84
Network connection	85
Configuring the Computer’s Network Settings	86
Setting Up the Network	89
Error Notification Mails	95
Controlling the Projector from a Computer	97
Adjusting the Image	99
Filling the Screen	99
Selecting Screen Aspect	101
Selecting an Aspect Ratio	102
Relationship between Aspect and Screen Aspect	103
Adjusting Keystone Distortion	103
Horizontal/Vertical Keystone Correction	103
Corner Adjustment	104
Adjustment Using a Test Pattern	107
Special Arrangements	108
Projecting from Multiple Projectors at Once (Edge Blending)	108
Adjusting the Overlapping Area	110
Making Overlapping Edges Less Noticeable	112
Corner Adjustment	113
Using PC-Free Multi Projection	114
Menu Guide	118
Using Menus	119
Menu Configuration	122
Menu Description	128
Input settings	128
Aspect	129
Auto PC	129
Input signal select	129
Input signal settings	130
Input level	131
Super white	131
Color space	131
Progressive	132
Slideshow interval	132
Animation effect	132
PC-free multi projection	133
Mode setting	133
Layout pattern setting	133
Destination projector setting	133
Slideshow interval	134
Animation effect	134
Split screen	134
Input signal details	135
Image adjustment	136
Image mode	137
Create profile	137
Brightness	137
Contrast	137
Sharpness	138
Gamma	138
Color adjustment	138
Advanced adjustment	139
Ambient light	139
Random noise reduction	139
MPEG noise reduction	140
Mosquito noise reduction	140
Dynamic gamma	140
Colorimetry	140
Mem. color correct	141
6-axis color adjust	141
Fine-Tune Gamma	142
Lamp control	142
Lamp mode	143
Reset	143
Image priority	143
Install settings	144
Positional lock	145
Image flip H/V	145
Screen aspect	146
Zoom	146
Keystone	147
Digital image shift	147
Professional settings	147
RGB alignment	148
High altitude	149
Lens shift mode	149
Marginal focus	149
Edge blending	150
Lens - Position	153
Screen color	154
Test pattern	154
System settings	155
User screen settings	156
Logo capture	156
Logo position	156
No signal screen	156
Screen when blank	156
Projector on	157
On screen	157
Menu position	157
Menu display time	157
Guide	158
Show input status	158
NMPJ standby guide display	159
Split screen ID display	159
Lamp warning display	159
Air filter warning display	159
Overheat warning display	159
Remote control/Side control	160
Beep	160
Key repeat	160
Key lock	160
IR receiver settings	161
Remote control channel	161
[INPUT A-C] button settings	162
[Fn] button settings	162
Audio in terminal select	162
HDBaseT signal quality	163
Extron XTP	163
Serial communication	163
Power supply settings	164
Standby power setting	164
Power management mode	164
Power management duration	165
Direct power on	165
Motion blur reduction	165
Language	166
Other settings	167
Password settings	167
Register password	168
Date and time settings	168
Schedule	169
Detailed schedule setting	170
Gamma restore	172
Lamp counter	173
Air filter counter	173
Power counter	173
Firmware	173
Factory defaults	174
Network settings	175
Network settings lock	176
Network password setting	176
Register network password	176
Network (wired/wireless)	177
Detailed settings (wired)	178
Detailed settings (wireless)	182
PJLink	187
AMX Device Discovery	188
Crestron RoomView	188
Information	189
Checking Projector Information	190
Projector Web Screen Menu	191
Maintenance / Product Specifications / Troubleshooting	208
Maintenance	209
Cleaning the Projector	209
Cleaning the Air Filter	209
Replacing the Air Filter	210
Replacing the Lamp	212
Replacement Lamp	213
Lamp Replacement Procedure	214
Product Specifications	216
Supported Signal Types	216
Projector	218
Remote Control	220
Specification of Each Lens Unit (Option)	220
External View	222
Analog PC-2 / COMPONENT Terminal	223
Service Port (CONTROL)	223
Troubleshooting	226
LED Indicator Details	226
Symptoms and Solutions	227
You Cannot Turn on the Projector	227
You Cannot Project an Image from the Projector	228
There is no Sound	229
The Projected Image Is Blurred	229
You Cannot Project an Image Appropriately	230
The Projector Power Turns Off	230
The Projector Cannot Join the Network	231
You Cannot Operate the Remote Control	232
Index	234
Numerics	234
A	234
B	234
C	234
D	234
E	234
F	234
G	234
H	234
I	234
K	234
L	234
M	234
N	234
O	235
P	235
R	235
S	235
T	235
U	235
V	235
W	235
Z	235

Match case Limit results 1 per page

163

Menu Description

Menu Guide

Menu Description

Motion blur reduction

> [System settings] >

[Motion blur reduction]

Motion blur is blurring that occurs during video playback. Motion blur reduction can

make this blurring less noticeable.

Power management duration

Specify how much time must pass before the light source goes off or the projector enters

standby mode, depending on the [Power management mode] setting.

Option

Function

5 min. – 60 min.

After 30 seconds without an input signal when the projector is idle, the

projector starts displaying a countdown of the selected time.

Direct power on

You can turn on the projector by connecting the power cable without pressing the

POWER

button.

Option

Function

Off

The

POWER

button must be pressed to turn the projector on.

You can turn on the projector by connecting the power cable only.

Option

Function

Off

Motion blur reduction is not performed.

Weak

Reduce motion blur for fast-moving images. Note that images may

be slightly darker, and flickering may occur.

Strong

Reduce motion blur for images moving faster than with [Weak].

Note that images may be darker, and flickering may occur.

•

If setting the projector to [Strong] or [Weak] produces distracting flickering, set it to [Off].

•

[Motion blur reduction] is not available in [DICOM SIM] image mode. The menu is

grayed out.

•

Motion blur reduction is not available when [Lamp mode] is set to [Power saver 2].

•

If conditions that would start countdown are met while you are blanking projection,

blanking is canceled.

•

Once countdown begins, audio output stops.

•

Before enabling direct power on, be sure to set [Power management mode] to an

option other than [Disabled]. When [Disabled] is selected, [Direct power on] is not

available.

•

After turning off the projector, wait at least 5 minutes before turning it on again. It

may shorten the lamp life if you turn on the projector immediately after turning it off.

•

The projector is also equipped with a Direct Power Off feature. No damage is caused

to the projector even if it is unplugged during projection to turn it off without pressing

the

POWER

button. However, setting adjustments made immediately before

unplugging the projector may not be stored.