Canon VB-S905F Network Camera VB-S900F/VB-S905F Installation Guide - Page 2

Specifications Please refer to the installation procedures or "Operation Guide" for specifications not listed below. Camera Lens Fixed focal length lens (4x digital zoom) Viewing Angle For 16:9 aspect ratios Horizontal: 96.0° Vertical: 60.5° For 4:3 aspect ratios Horizontal: 77.0° Vertical: 60.5° Interface Network Terminal* Audio Input Terminal (common for LINE IN & MIC IN) External Device I/O Terminal Memory Card LAN x 1 (RJ45, 100Base-TX (auto/full-duplex/ half-duplex)) * LAN cables are category 5 or higher, with length 100 m (328 ft.) or shorter. 3.5 mm ( 0.14 in.) mini-jack connector (monaural) LINE IN x 1 or MIC IN x 1 Input x 1, Output x 1 microSD Memory Card, microSDHC Memory Card, microSDXC Memory Card Compatible. Others Operating Environment Temperature: -10°C - +50°C (+14°F - +122°F) Humidity: 5% - 85% (without condensation) Storage Environment Temperature: -30°C - +60°C (-22°F - +140°F) Humidity: 5% - 90% (without condensation) Power Supply PoE: PoE power supply via LAN cable (IEEE802.3af compliant) Power Consumption Max. 4.3 W - Class 2 power sourcing equipment (requests 7.0 W) Connecting the Camera Power Supply See "Specifications" > "Others" > "Power Supply". Important • Check with your dealer for more information about PoE devices. • Some PoE devices allow current limits for each port, but applying limits may interfere with performance. If using this type of PoE device, do not limit the operating current. • Some PoE devices have total consumption current limits for ports, which can interfere with performance when multiple ports are in use. For more information, check the instruction guide for your PoE device. External Device I/O Terminals  External Device Input Terminals (IN) The external device input terminal consists of a positive terminal (IN) and negative terminal (GND). Connecting cables to the positive and negative terminals and opening or closing the circuit notifies the Viewer. Important When connecting sensors and switches, use those that have terminals which are isolated from internal power and GND.  External Device Output Terminals (OUT) The external device output terminal consists of an OUT terminal and a GND terminal. Controls from the viewer can be used to open and close the circuit between the terminals. A MOSFET device is used for the output terminal. Rating range for load connected to output terminals. Rating between output terminals: Maximum voltage 50 V DC Continuous load current at or below 100 mA On resistance: Below 1 Ω Adaptive wiring for external device cables Rating Range: (same for contact input and output) Conductor Size: 0.42 - 0.80 mm ( 0.017 - 0.031 in.) dia. (AWG: No. 26 - 20) Stripped cable length should be approximately 11 - 13 mm (0.43 - 0.51 in.) Note • The External Device I/O Terminal consists of three terminals (IN, OUT, and GND). The GND terminal serves as both the external device input GND and the external device output GND. • The GND terminal is connected to the camera interior GND. • When using the external device input and output at the same time, couple the GND wire from the input cable with the GND wire from the output cable, conforming to the rating range, and connect it to the GND terminal. • Do not push the external device I/O terminal button with too much force. Doing so may cause the button to remain pushed-in. Internal Connection Diagram 10 kΩ 10 kΩ 0.1 µF 1 kΩ IN Input terminal GND OUT Output terminal Internal controller GND Audio Input Terminals Camera has single audio input system supporting two types of microphone input: LINE IN and MIC IN. Before use, change [Audio Input] on the Setting Page (see "Operation Guide"). LINE IN is selected by default. • Dynamic MIC IN Input impedence: 20 kΩ - 40 kΩ • Condenser MIC IN Input impedence (microphone bias resistance): 2.2 kΩ ±20% Microphone power supply: plug-in power (voltage: 2.3 V) * Supported microphones: Condenser microphones with plug-in power support • LINE IN Input level: up to 1 Vp-p * Use a microphone with an amplifier. Symbols Indicating Safety Precautions This Installation Guide uses the following marks to indicate important information the user should know in order to use the product safely. In this section, explanations are provided for each mark so that readers will understand the level of importance for each. Be sure to observe these items. Failure to follow the instructions Warning accompanied by this symbol may result in death or serious injury. Caution Failure to follow the instructions accompanied by this symbol may result in injury. Caution Failure to follow the instructions accompanied by this symbol may result in property damage. Important This symbol indicates important or restricted items. Note Contains reference information for operation or additional explanations. Safety Precautions Installation Precautions Warning Do not install in the following places: • Places in strong direct sunlight, near heat-generating objects, or subject to high temperatures • Places near fire sources or flammable solvents (alcohol, thinner, fuel, etc.) • Humid or dusty places • Places subject to oily smoke or steam • Places subject to sea air • Confined or enclosed places Fire or electric shock may result. Precautions for the LAN (power) cable: • Do not set any heavy objects on the LAN cable. • Do not pull, forcibly bend, scratch, or modify the LAN cable. Fire or electric shock may result. Caution For installation or inspection of this camera, consult the dealer where you purchased the product. • This installation should be made by a qualified service person and should conform to all local codes. • When installing on a ceiling, make sure the surface is capable of withstanding the total weight of the mounting bracket and the camera, and is sufficiently reinforced if necessary. • Be sure to use installation screws designed for the type of ceiling the camera is to be installed. • Periodically check the parts and screws for rust and to see if they have loosened, in order to prevent injuries and equipment damage due to falling items. • Do not install in unstable places, places subject to significant vibration or impact, or places subject to salt damage or corrosive gas. Failure to do so may result in the camera falling or other accidents. • Be careful not to trap your fingers during installation of the camera. Injury may result. Caution • Do not install the camera on an unstable or inclined surface. • After turning off the power, do not turn the power on again for at least 5 seconds. • Take measures to remove static electricity before performing any procedures. • If there is condensation, please wait to power on, until the condensation dissipates. Malfunction may result. • Take care not to damage wiring or pipes in the room. Damage to peripheral items may result. Precautions for Use Warning • If you discover defective conditions such as smoke, strange sounds, heat or strange odors, immediately stop using the camera and contact your nearest dealer. Fire or electric shock may result from continued use of the product. • If thunder starts, stop installation or inspection etc. and do not touch the camera or continue connecting the cable. • Do not disassemble or modify the camera. • Do not damage the connecting cable. • Do not spill water or other liquid inside the camera, spray the camera with water, or otherwise make it wet. • Do not insert foreign objects into the camera. • Do not use flammable sprays near the camera. • Do not leave LAN cables connected when the camera is not in use for long periods. • Do not use flammable solvents such as alcohol, paint thinner or benzine when cleaning the camera. Fire or electric shock may result. Only for European Union and EEA (Norway, Iceland and Liechtenstein) These symbols indicate that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/EU), the Battery Directive (2006/66/EC) and/or national legislation implementing those Directives. If a chemical symbol is printed beneath the symbol shown above, in accordance with the Battery Directive, this indicates that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in this battery or accumulator at a concentration above an applicable threshold specified in the Battery Directive. This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of waste could have a possible impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. Your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about the recycling of this product, please contact your local city office, waste authority, approved scheme or your household waste disposal service or visit www.canoneurope.com/weee, or www.canon-europe.com/battery. CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan CANON EUROPA N.V. Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands